RCU Forums - Search Results

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Notices
 
Search: Posts Made By: tippy
Showing results 1 to 25 of 500
Search took 1.11 seconds.
12-27-2009, 07:08 PM
Replies: 23
Views: 1,742
Posted By tippy

RE: Main rotor shaft slips

Posted in a new thread:
12-27-2009, 07:07 PM
Replies: 3
Views: 477
Posted By tippy

RE: Main rotor shaft update

And you're sorry for starting a completely new thread that is a continuation of your other thread? Now everyone is confused ... do we reply to this thread, the original thread, run both side by side...
12-19-2009, 11:07 PM
Replies: 1
Views: 390
Posted By tippy

RE: New Bees learning to pitch left & right

In other countries, driver side and passenger may be the opposite of your driver side and passenger side but their left and right will still be the same as yours. Use what ever keeps you flying...
12-19-2009, 11:02 PM
Replies: 8
Views: 616
Posted By tippy

RE: remote question

There are AA chargers that hold more than 4 batteries you know. I have two that can charge 10 AA's at a time (per charger). Like was said earlier, just make sure the AA's are "rechargeable".
12-11-2009, 12:59 PM
Replies: 2
Views: 484
Posted By tippy

RE: 12x programming

If I remember correctly, the knobs were only active (or the most active) at/around mid-stick because that was where hover use to be flown at (mid-stick). Today, it seems that even beginners are...
12-08-2009, 09:25 PM
Replies: 5
Views: 1,171
Posted By tippy

RE: collective and elevator control swapped

Glad to see you're off on the right foot. Just remember that when you are in the swash menu, you are adjusting FUNCTIONS and not Channels. So when you see A, E, and P ... these are FUNCTIONS. ...
12-06-2009, 09:05 PM
Replies: 7
Views: 1,832
Posted By tippy

RE: aileron gyro

You mean like you do for the tail rotor servo? Rather the opposite of wise ...

If you have a eCCPM heli, the aileron channel is also used to for the collective function and the elevator...
12-06-2009, 08:53 PM
Replies: 5
Views: 1,115
Posted By tippy

RE: Futaba 8UH & Telebee 701 gyro?

If you really have an 8UHx and not an 8UHxs (super) then you don't have the gyro menu option (per the Futaba website http://www.futabarc.com/manuals/notes-8u.html )
12-06-2009, 08:31 PM
Replies: 5
Views: 1,171
Posted By tippy

RE: collective and elevator control swapped

First thing to do is learn the difference between reversing channels and reversing (swash) functions. With a eCCPM swash, these two things do NOT do the same thing.

I'd set your Swash settings...
08-21-2009, 08:29 PM
Replies: 6
Views: 1,492
Posted By tippy

RE: Beginner w/ CP PRO 2- outta control??

A gyro in rate mode does nothing to hold YAW. Only the mechanical trim will do that under controlled conditions. Even a heli without a gyro will hold YAW in a hover under the right conditions. ...
09-19-2008, 03:38 PM
Replies: 4
Views: 889
Posted By tippy

RE: Helicopter found

There's a heli club just south of Rancho Cordova on Eagles nest. http://www.svrw.com/
Might try there and see if anyone is missing a heli.
09-10-2008, 03:40 PM
Replies: 15
Views: 1,303
Posted By tippy

RE: Speed up my spin please :)

Ok gyro/atv settings have been discussed.

If your tail rotor is at max mechanical travel ... and you want more ...

You can try increasing tail rotor RPM. Increasing head speed also...
09-06-2008, 11:49 AM
Replies: 3
Views: 540
Posted By tippy

RE: HBFP is turning right

Never mind ... I just read your user name :D :D
09-06-2008, 11:47 AM
Replies: 10
Views: 913
Posted By tippy

RE: At What Point Do I Purchase a CCPM?

Offended, no. Confused, ahhhh ... yeah. Are you sure you're in the right thread?



The OP asked specifically about potential 3D helis thus the 3D suggestions. I don't know how you get...
09-06-2008, 05:31 AM
Replies: 3
Views: 653
Posted By tippy

RE: Head lock gyro question

Gyros sense angular velocities/rates. Hopefully your entire heli is YAWing at the same rate. As long as you can make the necessary connections, the gyro is not affected by some other electrical...
09-06-2008, 05:26 AM
Replies: 3
Views: 540
Posted By tippy

RE: HBFP is turning right

uhhhhh ... the heli yawed right and you added MORE right?? I think I see your problem. If the heli YAWS right, you should be correcting with LEFT rudder not right.
09-06-2008, 05:20 AM
Replies: 10
Views: 913
Posted By tippy

RE: At What Point Do I Purchase a CCPM?

You don't necessarily need CCPM to do 3D.
There are 3D capable non-CCPM helis out there (ie TT Raptor, etc)

Did you mean ... "At What Point Do I Purchase a CP?" ? (As opposed to Fix pitch...
09-02-2008, 02:47 PM
Replies: 12
Views: 2,378
Posted By tippy

RE: OS 50 SX engine cutoff when throttle applied

Fair enough. I was going by your post that read that you didn't have the hyper but the plain SX. I just assumed the H was for Hyper. The SX-H definitely has a different carb config than SX and it...
09-02-2008, 12:03 PM
Replies: 19
Views: 1,857
Posted By tippy

RE: OS 50 engine problems

Ideally ... you should not have to adjust this needle ... the manual even says this. However, things happen ... dirty needle, change of fuel, engine tech had a bad day at the factory, faulty O-ring,...
09-02-2008, 11:39 AM
Replies: 12
Views: 2,378
Posted By tippy

RE: OS 50 SX engine cutoff when throttle applied

The Find (Figure) Numbers (FN) are the numbers in the little bubbles.
That would be FN 2 ( the part that has an arrow pointed at it called mixture adjustment). This the low mixture adjustment.
...
09-01-2008, 02:23 PM
Replies: 5
Views: 1,618
Posted By tippy

RE: Swash plate HELP

http://dtipton.home.att.net/img/H-1.jpg

Like the others have said ... H-1 is setting for a Raptor ... just thought I'd elaborate if you haven't figured out why it's got to be H-1.

"pure...
09-01-2008, 01:55 PM
Replies: 19
Views: 1,857
Posted By tippy

RE: OS 50 engine problems

This is not true. I posted in your thread that the low/idle mixture adjust is inside the throttle rotor. Look through the hole in the center of the throttle arm nut and deep inside the throttle...
09-01-2008, 01:24 PM
Replies: 12
Views: 2,378
Posted By tippy

RE: OS 50 SX engine cutoff when throttle applied

Looking at the 50sx-40-46-61-91fx manual, PG 15 shows the 50SX & 40/46FX have a 40B carb. I just looked at my 46FX and it has a 40B carb and it DOES have a low end mix adjustment deep inside the...
08-28-2008, 02:08 PM
Replies: 2
Views: 486
Posted By tippy

RE: 9303 2.4 radio

better without ...
08-20-2008, 03:40 PM
Replies: 14
Views: 2,654
Posted By tippy

RE: Belt CP Spinning Help!

gyro reversed ???

gyro reversed and rudder reversed are two different things. rudder reversed simply means the rudder response is backwards to stick responsed. gyro reversed is gyro response...
Showing results 1 to 25 of 500
 


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service - Do Not Sell My Personal Information

Copyright 2018 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.