Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Notices
 
Search: Posts Made By: flyrc100
Showing results 1 to 25 of 218
Search took 0.64 seconds.
07-30-2010, 11:08 AM
Replies: 8
Views: 1,377
Posted By flyrc100

RE: Poulan 46cc Intake problem

Thanks, I have two ideas on how to do this now!
07-29-2010, 07:18 AM
Replies: 8
Views: 1,377
Posted By flyrc100

RE: Poulan 46cc Intake problem

Thanks, unfortunately Brillelli is out of business I believe, that looked like a round holed version. I could make a round hole adapter myself, but the oval would be a challenge. Still, its a start,...
07-28-2010, 10:15 PM
Replies: 8
Views: 1,377
Posted By flyrc100

Poulan 46cc Intake problem

Ive got a Poulan 46cc Im converting. The intake is a rubber boot that slips over an oval shaped intake riser. If anyone is familer with this setup, how do you actually secure the carb and intake to...
04-28-2010, 12:29 PM
Replies: 13
Views: 1,754
Posted By flyrc100

RE: EI Timing for conversion engine

This is to W8ye's Post-I agree the timing (total at WOT) should be around 30 degrees, but that does not mean you should set it up there, does it? Should it not idle at 4 degrees (or so) and...
04-28-2010, 08:01 AM
Replies: 13
Views: 1,754
Posted By flyrc100

EI Timing for conversion engine

Im putting an EI on a Homelite 30cc. I set up the intial timing around 4 degrees BTC. It flip starts and idles just super, but it does not make Good top RPM, it gets to about 6300 and thats it, this...
03-28-2010, 10:18 AM
Replies: 1
Views: 747
Posted By flyrc100

Poulan 25cc Featherlite needs help

Hi,

Ive got a Poulan trimmer engine I converted. It runs OK, easy starts , good idle. The problem is it acts cold at full rpm. It runs rich for about 10 seconds at WOT , then its like it heats...
03-27-2010, 01:09 PM
Replies: 11
Views: 1,538
Posted By flyrc100

RE: Poulan 42cc installing EI need help!

Pretty clever way to adjust the timing, was the ring holding the magnet made to fit the Crank Taper? I guess to adjust the timing you would loosen the prop hub, loosen the bolt on the magnet ring,...
03-26-2010, 09:03 PM
03-26-2010, 06:25 PM
Replies: 11
Views: 1,538
Posted By flyrc100

RE: Poulan 42cc installing EI need help!

Its automatic advance, thanks!
03-26-2010, 03:05 PM
Replies: 11
Views: 1,538
Posted By flyrc100

Poulan 42cc installing EI need help!

Hi, Ive got a 42cc Poulan that I want to put an EI unit on. Other than the challenge of making some kind of bracket to hold the sensor, I was wondering if anyone had ever done one, and what the best...
01-23-2010, 11:27 PM
Replies: 6
Views: 828
Posted By flyrc100

RE: Dammitall ! Lost the stupid little magnet

The magnet will re-appear only after I buy a new one, thats the way it works. Does it have to be a rare earth magnet, or will any type do? Radio shack is a great suggestion BTW did not know,,Thanks
01-23-2010, 08:48 PM
Replies: 6
Views: 828
Posted By flyrc100

Dammitall ! Lost the stupid little magnet

That I neeed to put in the prop hub for the CRRC ignition I'm tinkering with! Where do you get a replacement? Thanks!
01-23-2010, 07:37 PM
Replies: 12
Views: 1,284
Posted By flyrc100

RE: Magnet installation for Ie how to?

The hook it up and try it thing worked, glad someone said something before I smashed it in place! Actually the magnet works with reverse roation if its upside down.
01-23-2010, 01:33 PM
Replies: 12
Views: 1,284
Posted By flyrc100

RE: Magnet installation for Ie how to?

Hmmm, The south pole needs to face sensor, dumb question, how do I figure that out? Thanks
01-23-2010, 10:17 AM
Replies: 3
Views: 785
Posted By flyrc100

RE: Ryobi, convert to IE?

Thanks for the advice!
01-23-2010, 10:15 AM
Replies: 12
Views: 1,284
Posted By flyrc100

RE: Magnet installation for Ie how to?

Thanks for the input gents, sounds like the epoxy method is what I will try first.
01-22-2010, 10:27 PM
Replies: 12
Views: 1,284
Posted By flyrc100

Magnet installation for Ie how to?

Hi, I am going to install a Magnet for an IE in my prop hub, any advice on a good techinque to keep it in place? Press fit, glue it? What kind of glue? Whatever, Thanks!
Forum: Gas Engines
01-22-2010, 11:21 AM
Replies: 1
Views: 187
Posted By flyrc100

RE: Ryobi 31cc ie setup

Sorry, I posted the same question on the conversion engine forum, thought it did not work and reposted here!
Forum: Gas Engines
01-22-2010, 11:17 AM
Replies: 1
Views: 187
Posted By flyrc100

Ryobi 31cc ie setup

Hi, I have a Ryobi 31cc and a CRCC IE ignition, any ideas on how to setup timing, and what should the gap be between the sensor and magnet? Thanks!
01-22-2010, 09:50 AM
Replies: 3
Views: 785
Posted By flyrc100

Ryobi, convert to IE?

Ive got a Ryobi 31cc and a Crcc ignition. Need some help, never put a IE on before! Has anyone set this up before? What should I set the initial timing at? What kind of gap do I need between the...
05-07-2009, 10:56 PM
Replies: 0
Views: 135
Posted By flyrc100

Pictures will not load on Ad

This is all too common now with RCU, RCU takes two bucks out of my account since I am "pro seller", and the pictures will not load onto the Ad. Second time this has happened. What to do? My Ad has...
04-23-2009, 07:24 AM
Replies: 4
Views: 956
Posted By flyrc100

RE: Photos won't Load

RCU never fixed it, I had to reboot my computer and then it worked, good luck!
03-15-2009, 01:50 PM
Replies: 4
Views: 956
Posted By flyrc100

Photos won't Load

My Photos will not load onto my Ad. The file size is about 150kb on the JPEGS, I've done it before, whats up?
02-16-2009, 08:44 AM
Replies: 8
Views: 2,165
Posted By flyrc100

RE: turnigy accucell-6 how to resume charing?

I finally figured out the safety timer thing. I was trying to change it while I was charging. You have to be in programming mode to actually be able to edit. Now I can play with it and see how well...
02-15-2009, 12:00 AM
Replies: 8
Views: 2,165
Posted By flyrc100

RE: turnigy accucell-6 how to resume charing?

Waterpumpers reply gave me hope, but when I put the menu on the saftey timer menu I hit the start button per his instructions. It just jumped to another menu. tried it several times. Maybe there is...
Showing results 1 to 25 of 218
 


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service - Do Not Sell My Personal Information -

Copyright 2018 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.