RCU Forums - Search Results

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Notices
 
Search: Posts Made By: canabus
Showing results 1 to 25 of 99
Search took 0.05 seconds.
10-15-2021, 10:21 PM
Replies: 7
Views: 2,852
Posted By canabus

The MFA Spear/Spearfish is a great handling boat...

The MFA Spear/Spearfish is a great handling boat from the English Fairey Boats.
We have one in our club running a Hobbyking 3648-1450kv on a 5800mah 4S Lipo battery, 120Amp ESC and a CNC 2 blade...
08-24-2021, 04:13 AM
Replies: 2
Views: 1,192
Posted By canabus

HI The Nitro 7.5 is about 2.65Hp @ 25000rpm...

HI
The Nitro 7.5 is about 2.65Hp @ 25000rpm !!!
You would require a brushless motor like a XK3674-1900kv on 4S Lipo battery to get a bit over equal power.
Also a 120 Amp ESC for a speed...
06-14-2020, 04:42 AM
Replies: 4
Views: 795
Posted By canabus

Parallel three batteries and use the other for...

Parallel three batteries and use the other for accessories.
Canabus
11-21-2017, 03:34 AM
Replies: 7
Views: 777
Posted By canabus

Hi All I have had three years of buying...

Hi All
I have had three years of buying Hobbyking parts for my boats including props, ESCs, motors, radios, servos and batteries.
Only had one problem in the parcel arrived very damage and was...
08-15-2017, 08:46 PM
Replies: 6
Views: 1,066
Posted By canabus

Hi Bill Model Boats magazine is separate to...

Hi Bill
Model Boats magazine is separate to Marine Modelling International and Traplet.
So Model Boats Magazine is the only one left !!!
We in Tasmania, Australia get the mags about two months...
08-15-2017, 05:33 PM
Replies: 6
Views: 1,066
Posted By canabus

Hi Bill Check on those website forums as...

Hi Bill
Check on those website forums as Traplet plans have been taken over my another company, but, MMI magazine is history.

Canabus
08-14-2017, 08:49 PM
Replies: 6
Views: 1,066
Posted By canabus

Hi Bill Try these other forums Model Boat...

Hi Bill
Try these other forums Model Boat Mayhem (http://www.modelboatmayhem.co.uk/)
Model Boats, model boats magazine (http://www.modelboats.co.uk/) ...
07-04-2017, 04:39 AM
Replies: 2
Views: 1,218
Posted By canabus

Hobbyking G60-500kv, 100A ESC's, 4S Lipo...

Hobbyking G60-500kv, 100A ESC's, 4S Lipo Batteries and 50mm 2 blade props(left and right hand).
05-21-2017, 02:01 AM
Replies: 9
Views: 1,434
Posted By canabus

Hi I would use a Hobbyking 3639-1100 kv 800...

Hi
I would use a Hobbyking 3639-1100 kv 800 watt 35mm brushless motor, 60Amp ESC, Lipo battery 4S (14.8 volts) 5800mah 40c and a 2 blade 40-45mm prop.
08-20-2016, 06:03 AM
Replies: 5
Views: 1,768
Posted By canabus

Hi Mate I thought it help you, nice lot of...

Hi Mate

I thought it help you, nice lot of guys!!!
08-20-2016, 05:59 AM
Replies: 5
Views: 1,768
Posted By canabus

Hi My hat is off to you, 81 and still building...

Hi
My hat is off to you, 81 and still building model boats!!!
We can not die , we have too many lovely boats to built!!!
Some of the new kits are laser cut and are a builder's dream!!!

Regards...
08-20-2016, 02:58 AM
Replies: 5
Views: 1,768
Posted By canabus

Hi Don and Max The Commander is a nice boat...

Hi Don and Max

The Commander is a nice boat ,but, the wood they use in the old kits was a bit crappy!!

An old boat builder, it all comes back and the new radios, brushless motors, ESC's and...
08-20-2016, 02:34 AM
Replies: 37
Views: 2,647
Posted By canabus

H Gun Tech I would offer a low price because...

H Gun Tech
I would offer a low price because for the size and amount of work in restoring it.

I would look at rust in the boat.

Post pictures of the boat on all forum sites, but, it is going...
08-13-2016, 10:42 PM
Replies: 2
Views: 616
Posted By canabus

A Turnigy TGY-IA6 from Hobbyking, good unit I...

A Turnigy TGY-IA6 from Hobbyking, good unit I have used one for two years with no problems.
Servos are extra, for a tug with a large rudder.
A Trackstar TS-400MG or Trackstar TS-410MG, any 9.45 KG...
08-13-2016, 10:34 PM
Replies: 4
Views: 542
Posted By canabus

I used a solid piece of aluminium rod drill a 1/8...

I used a solid piece of aluminium rod drill a 1/8 hole thru the middle on the lathe(or drill press), changed to a drill size for the prop shaft and drill half way thru.
Placed the rod into a drill...
08-08-2016, 02:27 AM
Replies: 5
Views: 701
Posted By canabus

Hi Bob1307 Scan the bulkheads from the plans...

Hi Bob1307
Scan the bulkheads from the plans and save them as PDF files.
Measure the bulkheads in mm's and to get to 6.5 inches(165mm) calculate the % difference and in the printer setup you can...
08-05-2016, 05:12 AM
Replies: 3
Views: 1,779
Posted By canabus

Hi Chris I use Hobbyking 35mm outrunners with...

Hi Chris
I use Hobbyking 35mm outrunners with and without engine water cooling mounts(3639-750,3639-1100,D3548/4-1100 and 3648-1450kv) the motors will only get hot if you run too larger prop(a 40mm...
07-10-2016, 03:39 AM
Replies: 13
Views: 2,218
Posted By canabus

Try slow drilling and hope the drill grips it,...

Try slow drilling and hope the drill grips it, or, after drilling down use a small thread tape!!!
07-10-2016, 03:32 AM
Replies: 1
Views: 517
Posted By canabus

Hi Log into http://www.modelboatmayhem.co.uk/...

Hi
Log into http://www.modelboatmayhem.co.uk/ and http://www.modelboats.co.uk/ these are very helpful boys.
The Resin hull would be easy repaired a local boat or car club would help you.
The radio...
07-08-2016, 04:53 AM
Replies: 6
Views: 1,593
Posted By canabus

I found some wrestling figure's with bendable...

I found some wrestling figure's with bendable limbs in a cheap shop for $2AU each about 1/12 scale.

Also some for 3/4" to the foot in the kids section of a large department store, $7AU for...
06-11-2016, 09:13 PM
Replies: 6
Views: 1,593
Posted By canabus

I found some figures for 3/4" to the foot scale...

I found some figures for 3/4" to the foot scale in the kids section of a large shop.
These were action military one's, swivel at the neck, shoulders, elbows, waist, tops of legs, knees.

Six...
05-03-2016, 06:43 PM
Replies: 1
Views: 1,259
Posted By canabus

For the 27" mono hull a B28-57-17L (630watts)on a...

For the 27" mono hull a B28-57-17L (630watts)on a 2650mah 3s Lipo battery 45A ESC, prop 32mm 1.4 pitch 2blade.
To increase speed later change battery to 4S( adds about 7000rpm).
I have the PDF...
05-03-2016, 06:27 PM
Replies: 6
Views: 1,248
Posted By canabus

Hi Dan Car ESC's ID (HK_45A, HK-60A SL and...

Hi Dan
Car ESC's ID (HK_45A, HK-60A SL and HK-100A).

Programming card ID (HK Prog-card).

Motors
3648-850 (T3648-850).
3639-750 (T3639-750).
3639-1100(T3639-1100).
D3548-1100(D3548-1100).
04-28-2016, 11:05 PM
Replies: 6
Views: 1,593
Posted By canabus

Hi Jon Some English companies do figures but...

Hi Jon
Some English companies do figures but yes large scale is a problem.

I build a old speed boat at 1/12 scale and only found the size I required in a cheap shop as wrestling figures.

OK...
04-28-2016, 10:56 PM
Replies: 6
Views: 1,248
Posted By canabus

Hi Dan I have been using the Hobbyking 3639-...

Hi Dan
I have been using the Hobbyking 3639- 750,1100 and 3648-850 with the car ESC (hk45 to 100A).
My original 3639- 1100kv dropped a bearing after 3 years(replacement $5) running most weekends.
...
Showing results 1 to 25 of 99
 


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service - Do Not Sell My Personal Information -

Copyright 2021 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.