RCU Forums - Search Results

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Notices
Search: Posts Made By: Hot Rod Todd
Showing results 1 to 12 of 12
Search took 0.01 seconds.
06-27-2017, 05:24 AM
Replies: 391
Views: 82,165
Posted By Hot Rod Todd

I made the fuel caps with aluminum tape. Cut...

I made the fuel caps with aluminum tape. Cut them out, add a layer, use a pen to engrave the details. Paint them red and stick them on the circle provided.
06-27-2017, 04:54 AM
Replies: 391
Views: 82,165
Posted By Hot Rod Todd

I made some adjustments, added some additional...

I made some adjustments, added some additional nose weight and completed some final detailing. The wing guns were made in the mold, but unfortunately are not very scale in size. They are hollow...
06-15-2017, 06:37 AM
Replies: 391
Views: 82,165
Posted By Hot Rod Todd

I have a few more details to go, but decided to...

I have a few more details to go, but decided to maiden my Mustang. First flight I had some engine problems (always fun) and it seemed the CG was a bit far back at the recommended point. I got it down...
06-09-2017, 06:44 AM
Replies: 391
Views: 82,165
Posted By Hot Rod Todd

Here's how I removed the original graphics. ...

Here's how I removed the original graphics. Lightly sand to remove the clear coat. A fine sanding sponge can work well for this, but takes a while. Use some Acetone to soften up the graphic, and...
06-09-2017, 05:25 AM
Replies: 391
Views: 82,165
Posted By Hot Rod Todd

Maschar, even though my guess is that you're the...

Maschar, even though my guess is that you're the guy who sells the exhausts, I'll provide a report on my install.

Because I was converting my Gunfighter into the Millie G, I knew the exhausts...
02-17-2017, 12:03 PM
Replies: 391
Views: 82,165
Posted By Hot Rod Todd

I had a TopRC Zero and now a Mustang, and the...

I had a TopRC Zero and now a Mustang, and the wing tube's seem tight. I'll check my Mustang over closely.

I would think it shouldn't be that hard to determine if the play is in the wing or the...
02-06-2017, 09:07 AM
Replies: 391
Views: 82,165
Posted By Hot Rod Todd

SWK550, I know you don't have the 55RA on yours,...

SWK550, I know you don't have the 55RA on yours, but I would still put a heat shield between the muffler and the carb. In a P-51 cowl it can get tight enough that you get heat soak that can cause...
01-30-2017, 09:03 AM
Replies: 391
Views: 82,165
Posted By Hot Rod Todd

Hopefully more than one set, because he ordered a...

Hopefully more than one set, because he ordered a set for me. Because I'll be doing a scheme without the exhaust shrouds, I'll need some good looking stacks.
01-24-2017, 05:39 AM
Replies: 391
Views: 82,165
Posted By Hot Rod Todd

I heard that only the tires are made by ESM, the...

I heard that only the tires are made by ESM, the retracts are something else and a bit better quality. I had them on my TopRC Zero and they worked fine. I opted for air on the Mustang, so I'll be...
01-21-2017, 07:31 AM
Replies: 391
Views: 82,165
Posted By Hot Rod Todd

The main problem with the leading edge of the...

The main problem with the leading edge of the rudders is that the rudder hits against the back of the shipping box (look at your box, you'll see where it hit). Any push and the rudder is flexed...
01-18-2017, 06:42 AM
Replies: 391
Views: 82,165
Posted By Hot Rod Todd

I'll be using the most common, 14985. It will be...

I'll be using the most common, 14985. It will be the easiest to convert from the Gunfighter. There's even the survivor scheme with the yellow name (I prefer the red). Callie graphics will make me...
01-18-2017, 05:42 AM
Replies: 391
Views: 82,165
Posted By Hot Rod Todd

My Gunfighter scheme P-51 arrives today. I too...

My Gunfighter scheme P-51 arrives today. I too plan on changing it to "The Millie G." I always prefer a real WW2 scheme that will allow me to weather the plane and give it the realistic look. I'll...
Showing results 1 to 12 of 12


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service - Do Not Sell My Personal Information

Copyright 2018 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.