Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Notices
 
Search: Posts Made By: TEBerg
Showing results 1 to 25 of 476
Search took 0.74 seconds.
Replies: 699
Views: 110,160
Posted By TEBerg

I'm ok leaving it on here.. I just didn't want...

I'm ok leaving it on here.. I just didn't want to promote other products in the discussion.

As it happens, I just ordered an IGyro 1e to put in a warbird. I can only have rudder gyro in...
Replies: 699
Views: 110,160
Posted By TEBerg

Good point - did you isolate the gyro with two...

Good point - did you isolate the gyro with two layers of the gyro tape/foam? It could just be the vibration. I used to see that cause procession in either/both directions though..
Replies: 699
Views: 110,160
Posted By TEBerg

You are experiencing 'creep' in heading hold...

You are experiencing 'creep' in heading hold mode.

This used to happen with older gyros when the temperature changed. You would/could use sub-trim to counter the creep.

The 401 recommends...
Forum: Kit Building
05-26-2020, 05:54 PM
Replies: 13
Views: 630
Posted By TEBerg

I built the New Era III from the Airtronics kit.....

I built the New Era III from the Airtronics kit.. I had bought it back when I first started flying in the 70's but waited until the 90's to build her..

It is a fast little plane.. I had a pretty...
Forum: Sport Flying
05-08-2020, 09:59 AM
Replies: 3
Views: 1,090
Posted By TEBerg

Yep, I use the clear 'rubbery' medical tape. ...

Yep, I use the clear 'rubbery' medical tape. Works well and seems to stick very well. Not the paper tape.
04-13-2020, 03:03 PM
Replies: 2
Views: 1,695
Posted By TEBerg

Nice videos and review. I have my Shrike set...

Nice videos and review.

I have my Shrike set up with ailerons/flaps, full span ailerons, elevator/flap mixing, camber, reflex, and crow.

Just for fun..

It's a nice plane, and I hope to fly...
Forum: ARF or RTF
12-11-2019, 09:39 AM
Replies: 5
Views: 1,012
Posted By TEBerg

Mine currently looks a little different.. See...

Mine currently looks a little different.. See Attached photo.

But, when I get done with setting up the DC-3, I'm going back to a single engine.

I'm planning to put either the Saito 100 FA on...
11-19-2019, 11:52 AM
Replies: 9
Views: 1,017
Posted By TEBerg

I wanted to jump in with a quick question and...

I wanted to jump in with a quick question and maybe an answer.

Do you have a Club or group near you flying RC? Visit with them and they may provide some answers to your questions.

Because,...
Forum: The Clubhouse
11-18-2019, 01:26 PM
Replies: 70
Views: 30,978
Posted By TEBerg

Steve, Thanks Again for all of your work on...

Steve,

Thanks Again for all of your work on the plans.

Another club member has just built the smaller bench. I'm sure there will be a couple more in the works..

Tom
10-28-2019, 08:44 AM
Replies: 11
Views: 1,102
Posted By TEBerg

It sounds like you are trying to fit the valve...

It sounds like you are trying to fit the valve directly into your pump, but it does not fit/work that way.

The Valve and Filler are meant to fit together and each have an air line. One air line...
10-16-2019, 01:24 PM
Replies: 20
Views: 3,815
Posted By TEBerg

Update

I've been flying the Twin Stick for a while.. Still want to add a gyro onto the rudder just to figure out how it will work on the DC-3 project.

I can't say this is my "favorite" flying plane. It...
Forum: Kit Building
10-16-2019, 12:54 PM
Replies: 3
Views: 793
Posted By TEBerg

I replied to this topic in the beginners thread. ...

I replied to this topic in the beginners thread. Found an electronic article for you, but not the kit instructions.
Forum: Beginners
10-16-2019, 12:07 PM
Replies: 4
Views: 982
Posted By TEBerg

I don't have the plans from the kit. ...

I don't have the plans from the kit.

However, I found a copy of the original New Era 40 Article Here: R/C Modeler Plan and Article Series: "RCM *New Era 40* Article and Plan"...
Forum: The Clubhouse
10-14-2019, 10:37 AM
Replies: 70
Views: 30,978
Posted By TEBerg

Just a quick note to post a photo of our new...

Just a quick note to post a photo of our new Start Bench.

I'm going to send a couple of little corrections/suggestions to help clean up these already great plans.

The guys loved the bench and...
08-12-2019, 12:57 PM
Replies: 20
Views: 3,815
Posted By TEBerg

Thanks, I appreciate the kind words..

Thanks, I appreciate the kind words..
08-12-2019, 08:26 AM
Replies: 20
Views: 3,815
Posted By TEBerg

Twin Ultra Stick has Flown

I got her out to the field and made three flights yesterday (Sunday, August 11, 2019). I must say she flies different than any other plane I have..

The photos below include a quick catch up on...
08-08-2019, 07:21 AM
Replies: 20
Views: 3,815
Posted By TEBerg

Spent some time getting a couple of decorations...

Spent some time getting a couple of decorations on the plane.

I thought about leaving it 'clean' but decided I liked putting the name on it, it helps me remember [laugh]. I also wanted to get it...
08-06-2019, 01:32 PM
Replies: 20
Views: 3,815
Posted By TEBerg

Thanks Scott.. I think I'm looking forward to...

Thanks Scott.. I think I'm looking forward to flying it [laugh]..

Couple more little fiddly things to work around getting the electronics in. Like the rudder servo wire up against the former;...
Forum: Kit Building
08-05-2019, 03:04 PM
Replies: 5
Views: 598
Posted By TEBerg

I have done a couple of things when I had...

I have done a couple of things when I had fuselage clearance issues.

Sadly, MACs Pipes is no longer in business due to the owner passing. However, I used a Tuned one-piece muffler that cleared...
08-05-2019, 10:12 AM
Replies: 20
Views: 3,815
Posted By TEBerg

Finished up getting the Tail Feathers on the...

Finished up getting the Tail Feathers on the project. First photo is probably what the Twin Ultra Stick would look like taking an ARF out of the box...

Then, I went back to the wing and installed...
Forum: Beginners
08-05-2019, 09:01 AM
Replies: 8
Views: 2,009
Posted By TEBerg

When I did my 'building table' I chose a...

When I did my 'building table' I chose a solid-core door. The hollow core options did not make the span over my opening and would bow. You're folding table should provide the extra support.

I...
07-30-2019, 11:12 AM
Replies: 20
Views: 3,815
Posted By TEBerg

I got most of the GUTS into the wing. All the...

I got most of the GUTS into the wing. All the servos are mounted, working, and color coded.

Moving on to the fuselage/tail feathers next.
Forum: Beginners
07-30-2019, 09:33 AM
Replies: 24
Views: 3,188
Posted By TEBerg

I use the "pinch" test for my 2-stroke engines.. ...

I use the "pinch" test for my 2-stroke engines..

With the plane level and open full throttle: Quickly pinch (just long enough to stop fuel flow - less than half a second) the fuel line somewhere...
07-29-2019, 07:57 AM
Replies: 34
Views: 3,650
Posted By TEBerg

When I click on the "Go Advanced" button located...

When I click on the "Go Advanced" button located below the Quick Reply; it takes me to a "Reply to Thread" box that has four sections.
Title:
Message:
Current Attachments (Manage Attachments Link)...
07-24-2019, 08:34 AM
Replies: 20
Views: 3,815
Posted By TEBerg

Last items on my Ultra Stick Twin modification. ...

Last items on my Ultra Stick Twin modification.

I glued 1/2-inch triangle stock fairings behind the nacelles. I glued them in with canopy glue just to clean up the look a little and make the...
Showing results 1 to 25 of 476
 


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service - Do Not Sell My Personal Information -

Copyright 2018 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.