Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Notices
 
Search: Posts Made By: FalconWings10
Showing results 1 to 25 of 407
Search took 0.91 seconds.
Forum: Gas Engines
09-28-2009, 04:24 PM
Replies: 859
Views: 119,395
Posted By FalconWings10

RE: New ZDZ-80

Great input Tony. I was having the same issue.
Forum: Gas Engines
09-28-2009, 11:25 AM
Replies: 859
Views: 119,395
Posted By FalconWings10

RE: New ZDZ-80

Could be a weak or faulty diaphram. Keep priming until you can get it to start, look for bubbles in the fuel line. Do you have your vent line setup?
Forum: Gas Engines
09-25-2009, 09:16 AM
Replies: 859
Views: 119,395
Posted By FalconWings10

RE: New ZDZ-80

That's what I did. Took them out and cut them in half. Very carefully cut a screw driver knotch with a dremel and cutoff wheel.
Forum: Gas Engines
09-24-2009, 02:00 PM
Replies: 859
Views: 119,395
Posted By FalconWings10

RE: New ZDZ-80

All, finally got mine to start and run. There's nothing wrong with the Tillotson carb. A little different settings from the Walbro. I set the Tillotson to: H - 1.5, L - .75 (yes - .75). ...
12-10-2008, 05:48 PM
Replies: 20
Views: 11,009
Posted By FalconWings10

RE: Best Way to Add Weight to the Front of Your Plane

Not sure exactly how much weight I need to add. I'm in the Air Force and haven't had a chance to work on it since before Thanksgiving. Plane is a Carl Goldberg Edge 540. Seems well built and...
12-01-2008, 01:51 PM
Replies: 367
Views: 49,460
Posted By FalconWings10

RE: H9/Carden Yak 54

Has anyone had a problem with the horizontal stabs not fitting against the aft side of the fuse? Mine has about a 1/16" gap on both sides.
11-25-2008, 10:35 AM
Replies: 20
Views: 11,009
Posted By FalconWings10

RE: Best Way to Add Weight to the Front of Your Plane

All great ideas. My current build is glow. Got a 4 stroke out front.
11-25-2008, 07:45 AM
Replies: 20
Views: 11,009
Posted By FalconWings10

Best Way to Add Weight to the Front of Your Plane

I hate adding weight to a plane, however, after I've built the tail as light as I can and moved the electronics as far forward as possible, I still need more weight. How are you guys fixing the...
10-19-2008, 01:39 PM
Replies: 13
Views: 3,585
Posted By FalconWings10

10-19-2008, 01:37 PM
Replies: 367
Views: 49,460
Posted By FalconWings10

Replies: 155
Views: 17,394
Posted By FalconWings10

RE: Xtremelink

Thanks fellas. JC
Replies: 155
Views: 17,394
Posted By FalconWings10

RE: Xtremelink

Can't be vibration, ... does it in my shop with the engine off! Could it be the failsafe? I don't understand what it does and how it's set
Replies: 155
Views: 17,394
Posted By FalconWings10

RE: Xtremelink

Guys, I have one of these in my 1/3 Sukhoi and I'm afraid to fly it. While in the shop or just running the engine, my digital servos start moving very "jerky/rough" and then I completely lose the...
08-23-2008, 02:55 PM
Replies: 367
Views: 49,460
Posted By FalconWings10

Forum: ARF or RTF
03-22-2008, 05:37 PM
Replies: 243
Views: 39,580
Posted By FalconWings10

Forum: Gas Engines
01-05-2008, 07:39 PM
Replies: 859
Views: 119,395
Posted By FalconWings10

RE: New ZDZ-80

Cool thread! I just finished mounting one into a H9 Suk.
Forum: Glow Engines
06-22-2006, 12:00 AM
Replies: 27
Views: 1,736
Posted By FalconWings10

RE: Pumps for 4 strokes

I prefer the Cline. Simple, light, dependable.... what else can I say.
03-09-2006, 09:14 PM
Replies: 35
Views: 2,807
Posted By FalconWings10

RE: SUGGEST A NEW PLANE FOR TOP-FLITE!!!!!!

I know that it's not a warbird, but a GOOD model of the Spirit of St. Louis would be cool. High wing design for easy flight and lots of history.
02-18-2006, 01:43 PM
Replies: 637
Views: 51,323
Posted By FalconWings10

RE: New H-9 Sukhoi set up

Those of you that are using the DA-100. Did you have to cut the cowl for the motor to extend?
09-24-2005, 05:48 PM
Replies: 0
Views: 497
Posted By FalconWings10

MOVED: Using both JR Servos and Futaba Servos on the Same Receiver

RC Radios, Transmitters, Receivers, Servos, gyros: http://www.rcuniverse.com/forum/fb.asp?m=3389213
09-24-2005, 11:52 AM
Replies: 1
Views: 473
Posted By FalconWings10

Using both JR Servos and Futaba Servos on the Same Receiver

Danny, I have 8411 servos and want to use them with my Futaba RX. Is it possible?
Replies: 5
Views: 735
Posted By FalconWings10

Using both JR Servos and Futaba Servos on the Same Receiver

Has anyone ever used JR servos on a Futaba receiver? Or vice vrs?
09-10-2005, 01:58 PM
Replies: 637
Views: 51,323
Posted By FalconWings10

Forum: 3D Flying!
03-17-2005, 01:22 PM
Replies: 9
Views: 732
Posted By FalconWings10

RE: Plane for .91 4 Stroke??

I've seen the Kangke Extra300S/40 sport scale ARF fly with this engine. I know that this is a 40 size plane but the engine tucked in beautifully it was freakin awsome to watch!
Showing results 1 to 25 of 407
 


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service - Do Not Sell My Personal Information -

Copyright 2018 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.