RCU Forums - Search Results

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Notices
 
Search: Posts Made By: andrewskj
Showing results 1 to 25 of 104
Search took 0.60 seconds.
03-17-2020, 12:27 PM
Replies: 0
Views: 220
Posted By andrewskj

Timber X

New timber x cannot get AS3X to work. My rx binds ok normally I have Ar636A rx and using my dx9.. Anyone have this problem with timber please Help thanks Ken
02-16-2020, 07:23 PM
Replies: 3
Views: 346
Posted By andrewskj

Thanks Rusty Us

Thanks Rusty Us
02-16-2020, 07:20 PM
Replies: 3
Views: 346
Posted By andrewskj

Thank you

Thank you
02-15-2020, 10:33 AM
Replies: 3
Views: 346
Posted By andrewskj

Extended leads for this charger

Hello new to electric have spectrum s2100 need to extend leads on both batt to carver and balance do they make already made extensions and can you give me part numbers I don't want to solder up...
01-14-2020, 05:40 PM
Replies: 1
Views: 379
Posted By andrewskj

Timber x

Hello I just received my new timber x and would like to know if i use 4s 2200 batts do i need to use steel rod vs carbon in the tail or is that steel rod help to balance the 4s batts ?? Thanks in...
12-26-2019, 11:09 PM
Replies: 1
Views: 516
Posted By andrewskj

Safe way to store lipos

New to electric and need to know a safe way to store lipos that is inside or outside you home or in refrigerator freezer or lower part of frig ?? Don’t see many good articles addressing ‘‘tis...
08-08-2018, 09:18 AM
Replies: 5
Views: 321
Posted By andrewskj

Thanks for the info ....Ken

Thanks for the info ....Ken
07-29-2018, 09:49 AM
Replies: 5
Views: 321
Posted By andrewskj

Thanks Steve i appreciate it ...Ken

Thanks Steve i appreciate it ...Ken
07-27-2018, 06:03 PM
Replies: 5
Views: 321
Posted By andrewskj

Mc cor rc 59 plugs

Its very hard to find mccoy rc 59 plugs in stock but I see team associates mc 59 plug are very avail are they the same just under different vender ??? Thanks
Forum: Glow Engines
10-19-2017, 01:21 PM
Replies: 23
Views: 1,406
Posted By andrewskj

whats the best plug to use on the 52nx ????

whats the best plug to use on the 52nx ????
Forum: Glow Engines
10-18-2017, 11:30 AM
Replies: 23
Views: 1,406
Posted By andrewskj

Thanks Ken

Thanks Ken
Forum: Glow Engines
10-13-2017, 10:29 PM
Replies: 23
Views: 1,406
Posted By andrewskj

I just bought a 52 nx and want to get rid of the...

I just bought a 52 nx and want to get rid of the limiters how hard is it to remove the idle limiter... thanks Ken
09-12-2017, 04:49 PM
Replies: 3
Views: 593
Posted By andrewskj

Cool os 55ax installation problems

I just finished a new U can do SF but having problems with my engine and was wondering if its because of the position the engine is in that causes the problems . I changed the tank just for good...
07-28-2017, 10:49 AM
Replies: 1
Views: 439
Posted By andrewskj

os 55ax

Hello can you pleas tell me how to set the low end back to factory setting Thank you Ken
07-28-2017, 09:31 AM
Replies: 2
Views: 346
Posted By andrewskj

ucd sf engine problems

Hello has anyone that fly"s a UCD SF had problems with the engines up unable to adjust it does drip some fuel and I can't get it to have a steady mid it cuts out after running mid throttle ? I'm...
05-13-2017, 07:28 PM
Replies: 0
Views: 275
Posted By andrewskj

best servos for ucd sf

Whats the best servos for the new UCD SF i put in hs 485 by hitter very noise and chatter disappointed please help Thank you
05-13-2017, 11:30 AM
Replies: 5
Views: 608
Posted By andrewskj

Mixing servos

Can you mix servo brands on the same plane as long as you keep analog to analog and digital to digital ?? Will this cause any problems ?
05-08-2017, 06:48 PM
Replies: 2
Views: 468
Posted By andrewskj

cowl placement

Thanks for the help Ken
Forum: ARF or RTF
04-23-2017, 09:17 AM
Replies: 4
Views: 2,421
Posted By andrewskj

Hi David I have a question when you make the...

Hi David I have a question when you make the template and tape it I understand that but how do you place the cowl on plane to get proper spot to match spinner and allow for small gap behind spinner...
04-18-2017, 08:53 PM
Replies: 2
Views: 468
Posted By andrewskj

U can do sf

Building U Can Do SF whats the easiest way to measure and fit the cowl for os 55 > please help Im almost done but I need help here . Thank you Ken
Forum: ARF or RTF
04-18-2017, 01:19 PM
Replies: 4
Views: 2,421
Posted By andrewskj

U can do sf

Building U Can Do SF whats the easiest way to measure and fit the cowl for os 55 > please help Im almost done but I need help here . Thank you Ken
Forum: ARF or RTF
02-26-2017, 12:51 PM
Replies: 1
Views: 390
Posted By andrewskj

U CanDo SF best tank construction

U can do sfbuilding u can do ss
f going with os 55 whats the best tank set up 2 line or 3 line and is there forum on the u can do sf thanks in advance love this site very helpful Ken
02-25-2017, 01:21 PM
Replies: 1
Views: 305
Posted By andrewskj

U can do sf

building u can do ss
f going with os 55 whats the best tank set up 2 line or 3 line and is there forum on the u can do sf thanks in advance love this site very helpful Ken
10-24-2016, 11:09 AM
Replies: 3
Views: 641
Posted By andrewskj

Yes i have a load on my meter Hobby meter digital...

Yes i have a load on my meter Hobby meter digital Thanks
10-23-2016, 09:54 PM
Replies: 3
Views: 641
Posted By andrewskj

airtronics rd 8000 glitch short time out air rec used

RD 8000 working perfect just started lose signal had 4 great flight and then problem any one have this problem . good range check got it back all servos work great battery full nitro plane engine ....
Showing results 1 to 25 of 104
 


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service - Do Not Sell My Personal Information

Copyright © 2018 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.