Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Notices
 
Search: Posts Made By: n8622t
Showing results 1 to 25 of 277
Search took 0.02 seconds.
01-24-2021, 11:21 AM
Replies: 1,192
Views: 234,469
Posted By n8622t

A shot at my panel and compression springs on the...

A shot at my panel and compression springs on the tailwheel ...
01-24-2021, 04:50 AM
Replies: 1,192
Views: 234,469
Posted By n8622t

yeah T you warned me about that...I guess it took...

yeah T you warned me about that...I guess it took some flying to loosen the set screw up enough that I could remove it without stripping out the 1/16 set screw. I hate when they use those
01-23-2021, 03:24 PM
Replies: 1,192
Views: 234,469
Posted By n8622t

sorry so long to get this to you but my elevator...

sorry so long to get this to you but my elevator deflections measured from the trailing edge is 25mm up and down low rates and 30mm up and down high rates...works great for me with 15% exponential
01-19-2021, 05:37 AM
Replies: 1,192
Views: 234,469
Posted By n8622t

I’ll get you my elevator “deflections”...

I’ll get you my elevator “deflections” today....anyone using the Sierra tailwheel be sure to pull the fork shaft out and put a flat spot on it where the shaft fits into the fork. I sure didn’t like...
12-19-2020, 06:30 AM
Replies: 1,192
Views: 234,469
Posted By n8622t

No problem, have fun with the build it’s a good...

No problem, have fun with the build it’s a good model
12-18-2020, 04:03 AM
Replies: 1,192
Views: 234,469
Posted By n8622t

hi lukey77, covid19 canceled all my flying for...

hi lukey77, covid19 canceled all my flying for 2020 except for the earlier posted flights but 2021 is looking good starting in January. The engine is a great match for the airframe for power and I...
11-11-2020, 08:29 AM
Replies: 1,192
Views: 234,469
Posted By n8622t

this is good time to find that problem😬

this is good time to find that problem😬
11-03-2020, 01:00 PM
Replies: 1,192
Views: 234,469
Posted By n8622t

they’re both good....just need to decide on...

they’re both good....just need to decide on finish, matte is best!😃
11-03-2020, 06:31 AM
Replies: 1,192
Views: 234,469
Posted By n8622t

perfect!!

perfect!!
11-02-2020, 05:59 PM
Replies: 1,192
Views: 234,469
Posted By n8622t

get a couple of cans of 2K Eastwood flat clear...

get a couple of cans of 2K Eastwood flat clear and it’ll be fuel proof!!
11-02-2020, 05:57 PM
Replies: 1,192
Views: 234,469
Posted By n8622t

Nice Work!!!

Nice Work!!!
08-16-2020, 08:41 AM
Replies: 1,192
Views: 234,469
Posted By n8622t

Jraycut you’ll be amazed how fast this prop will...

Jraycut you’ll be amazed how fast this prop will fly the model
08-16-2020, 08:37 AM
Replies: 1,192
Views: 234,469
Posted By n8622t

On the ground it maxed out at 6100. I used the...

On the ground it maxed out at 6100. I used the servo throttle endpoint to reduce rpm to 5200
08-15-2020, 01:36 PM
Replies: 1,192
Views: 234,469
Posted By n8622t

Jraycut what was the max rpm you were getting on...

Jraycut what was the max rpm you were getting on that prop? I have the same prop on my 160 7 cyl
08-14-2020, 06:31 PM
Replies: 1,192
Views: 234,469
Posted By n8622t

Sweeeeet!!

Sweeeeet!!
08-14-2020, 07:02 AM
Replies: 1,192
Views: 234,469
Posted By n8622t

Yeah just YouTube it then paste the link👍:cool:

Yeah just YouTube it then paste the link👍:cool:
07-27-2020, 01:07 PM
Replies: 1,192
Views: 234,469
Posted By n8622t

beautiful!! Good rudder work on the take off and...

beautiful!! Good rudder work on the take off and a nice flight
07-27-2020, 12:53 PM
Replies: 1,192
Views: 234,469
Posted By n8622t

definitely buy the CH-Ignition!! Turns a Moki...

definitely buy the CH-Ignition!! Turns a Moki into a different animal
07-18-2020, 03:27 AM
Replies: 1,192
Views: 234,469
Posted By n8622t

good plan....

good plan....
07-16-2020, 05:22 AM
Replies: 1,192
Views: 234,469
Posted By n8622t

too much toe in could increase the chance of a...

too much toe in could increase the chance of a nose over and toe out will make it squirrelly on the ground
07-16-2020, 05:19 AM
Replies: 1,192
Views: 234,469
Posted By n8622t

Jraycut, the worse that can happen is that you’ll...

Jraycut, the worse that can happen is that you’ll just have to stay focused a little more on the ground handling :p
07-15-2020, 11:49 AM
Replies: 1,192
Views: 234,469
Posted By n8622t

That’s crazy...that never works on models that...

That’s crazy...that never works on models that I’ve experienced
07-15-2020, 06:56 AM
Replies: 1,192
Views: 234,469
Posted By n8622t

could that be the 109 you’re referring too? Top...

could that be the 109 you’re referring too? Top flight calls for 0 toe in on their 190 as well
07-15-2020, 04:37 AM
Replies: 1,192
Views: 234,469
Posted By n8622t

Jraycut, that’s the big issue with the scale...

Jraycut, that’s the big issue with the scale Sierra 190 gear. The only thing I found possible was to slightly cut the gear rails to allow me to move the gear as far as possible. Of course that...
07-11-2020, 10:51 AM
Replies: 1,192
Views: 234,469
Posted By n8622t

Yer almost there:cool:

Yer almost there:cool:
Showing results 1 to 25 of 277
 


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service - Do Not Sell My Personal Information -

Copyright © 2021 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.