RCU Forums - Search Results

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Notices
Search: Posts Made By: tim.moland
Showing results 1 to 13 of 13
Search took 0.27 seconds.
12-23-2009, 05:11 PM
Replies: 1
Views: 4,699
Posted By tim.moland

Mamo models Upside down system

Ok, I have heard alot about the Mamo models Upside Down system, and have seen Brandon Chitty fly it to perfection. My only question is, Is it still available? If so, where? I have looked all over...
09-18-2009, 03:31 PM
Replies: 8
Views: 1,221
Posted By tim.moland

RE: How do I bench run an O.S. 91 to break in?

Sounds good. You can't get any better advice then that.
Forum: T-Rex heli
09-18-2009, 03:29 PM
Replies: 18
Views: 1,694
Posted By tim.moland

RE: My Trex 600 E will only fly for 30 secs.

Thanks guys. I will post again when I figure it out.
09-17-2009, 06:49 PM
Replies: 8
Views: 1,221
Posted By tim.moland

RE: How do I bench run an O.S. 91 to break in?

Thank you archiebald, you just made my life a whole heck of a lot easier. Besides, boring hovering is way better then looking at an engine running on the table
Forum: T-Rex heli
09-17-2009, 06:45 PM
Replies: 18
Views: 1,694
Posted By tim.moland

RE: My Trex 600 E will only fly for 30 secs.

Ok, I double checked the ESC, it is programed right. The cutoff point is programmed at 2.9 volts. I did some hovering this morning and took some additional data from each of the batteries. I flew...
09-16-2009, 10:24 PM
Replies: 8
Views: 1,221
Posted By tim.moland

RE: How do I bench run an O.S. 91 to break in?

Has anyone else bench ran a helicopter engine to break it in. I read in Ray's Helicopter manual to break it in on the bench with a prop he recommended to simulate the head speed(I cant remember the...
09-16-2009, 09:09 PM
Replies: 8
Views: 1,221
Posted By tim.moland

RE: How do I bench run an O.S. 91 to break in?

The 50 hub May fit the 90. The problem is the crankshaft on the 50 has a place for a woodruf key to hold the hub stationary, the 90 has no slot to accept the key, therefore leaving the hub useless. ...
09-16-2009, 06:39 PM
Replies: 8
Views: 1,221
Posted By tim.moland

How do I bench run an O.S. 91 to break in?

I am new to Nitro helicopters. I am wanting to bench run my O.S. 50 Hyper before installing it into the helicopter. I purchased a hub assembly for that motor so I can use a conventional prop to do...
Forum: T-Rex heli
09-16-2009, 04:43 PM
Replies: 18
Views: 1,694
Posted By tim.moland

RE: My Trex 600 E will only fly for 30 secs.

I have yet to make it to the field to fly it again. Ill get back to you on the temp. of the esc. I will ask to borrow a battery from the other guy that flies a 600E at my field, or have him try my...
Forum: T-Rex heli
09-16-2009, 04:37 PM
Replies: 18
Views: 1,694
Posted By tim.moland

RE: My Trex 600 E will only fly for 30 secs.

I checked two of the four batteries after flying them. One pack showed 4.17 volts per cell. The other showed 4.13 volts per cell. Thats still a good charge isn't it, or did I figure wrong.
Forum: T-Rex heli
09-15-2009, 07:32 PM
Replies: 18
Views: 1,694
Posted By tim.moland

RE: My Trex 600 E will only fly for 30 secs.

The helicopter was sold through a hobby shop so i didnt have direct contact with the seller. I did however buy a Trex500 from the same individual and have had excellent results, so i don't think he...
Forum: T-Rex heli
09-15-2009, 07:10 PM
Replies: 18
Views: 1,694
Posted By tim.moland

RE: My Trex 600 E will only fly for 30 secs.

All four batteries are 6S. Two are air thunder 5000MaH. The other two are Flightpower 5350MaH. As I said before, all four batteries are used and came with the helicopter. I have no idea what...
Forum: T-Rex heli
09-15-2009, 04:44 PM
Replies: 18
Views: 1,694
Posted By tim.moland

My Trex 600 E will only fly for 30 secs.

I purchased a Trex 600 electric used. It came with four used lipos. After setting everything up on my DX7, I test flew it for the first time. A fully charged battery only lasted about thirty...
Showing results 1 to 13 of 13


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service - Do Not Sell My Personal Information -

Copyright 2021 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.