Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Notices
 
Search: Posts Made By: schokshi
Showing results 1 to 25 of 61
Search took 0.73 seconds.
Forum: Kit Building
11-03-2013, 06:35 AM
Replies: 2,180
Views: 237,814
Posted By schokshi

Hello Vincent, thank you for such a detailed...

Hello Vincent, thank you for such a detailed post. I am just about to order this kit. This will be my first ever build. Winter project! Thanks. i have DLE35RA which i will be using for this kit.
Forum: Gas Engines
09-28-2013, 12:21 PM
Replies: 12
Views: 4,024
Posted By schokshi

Thanks all for your replies, i have replaced DLE...

Thanks all for your replies, i have replaced DLE spark plug with NGK spark plug, also applied some dielectric grease on top, checked spark & it is working fine. low speed was 1 3/4 out & high speed...
Forum: Gas Engines
09-28-2013, 04:08 AM
Replies: 12
Views: 4,024
Posted By schokshi

Thanks, i have removed idle screw and adjusted...

Thanks, i have removed idle screw and adjusted end points so that full down trim on throttle completely closes carb with slight hint of binding. Generally how many clicks you open for from close for...
Forum: Gas Engines
09-27-2013, 05:34 PM
Replies: 12
Views: 4,024
Posted By schokshi

Also instructions on TBM site says to use lower...

Also instructions on TBM site says to use lower load during breakin. Recommended was 19x8 2 blade so I am using 17/10 3 blade prop
Forum: Gas Engines
09-27-2013, 05:30 PM
Replies: 12
Views: 4,024
Posted By schokshi

Initially idle screw was left as it came from...

Initially idle screw was left as it came from factory and I have now turned it out so I can close carb more, it will drop RPM but that's when knocking starts. I am relying on optic kill switch to...
Forum: Gas Engines
09-27-2013, 02:39 PM
Replies: 12
Views: 4,024
Posted By schokshi

Also, wanted to let you guys know that i am using...

Also, wanted to let you guys know that i am using a spark plug that came with an engine its DLE brand and using 93 octane 30:1 gas/oil mix
Forum: Gas Engines
09-27-2013, 02:19 PM
Replies: 12
Views: 4,024
Posted By schokshi

Need help with new DLE 35RA tuning

Hi,
I am new to gas engine. This is my first gas engine. I have installed this engine in old Hangar 9 ultra stick 120. When i first started it, with factory needle setting, i could never get idle...
Forum: Gas Engines
02-23-2012, 06:27 AM
Replies: 5
Views: 700
Posted By schokshi

RE: Need help with firewall for gas engine

Ahicks,
Thanks for your reply. Actually cutting 20 mm from middle section is very good idea that way i can maintain thrust angles. However when i join them together, can i just use 30 min epoxy? or...
Forum: Gas Engines
02-23-2012, 05:56 AM
Replies: 5
Views: 700
Posted By schokshi

Need help with firewall for gas engine

Folks,
I am new to gas engines. i have purchased RCGF 15 CC & am planning to install it in H9 Pawnee 40. It requires me to shorten engine box length by about 20 mm. I have never done this before &...
Forum: Gas Engines
02-11-2012, 03:49 PM
Replies: 3
Views: 774
Posted By schokshi

RE: Need help: 15 cc RCGF idle setting on Tx

Ahicks,
Thank you very much for your response. Lot of good information on that post specially beginner like me.
Forum: Gas Engines
02-11-2012, 03:10 AM
Replies: 3
Views: 774
Posted By schokshi

Need help: 15 cc RCGF idle setting on Tx

Hi,
I just purchased RCGF 15 CC gas engine and installing it in Kadet Senior. I have couple of questions about set up. This is the first time i am using gas engine:
1) It has welbro type carb and...
Forum: Beginners
10-25-2006, 11:50 AM
Replies: 0
Views: 362
Posted By schokshi

Suggestion for planes for small gas engine

I am looking for suggestions for an ARF for a small size gas engines such as Zenoah 20EI or 23 size.
This will be my third plane after LT-40 & US-60

Thanks for your replies
Forum: Beginners
10-18-2006, 03:42 AM
Replies: 4
Views: 887
Posted By schokshi

Ailron to Rudder Mixing - Help Needed

I have H9 J3 Cub PNP, can somebody give me recommendation for how much to mix rudder with ailron for co-ordinated turns?
Thanks
10-04-2006, 06:42 PM
Replies: 1
Views: 614
Posted By schokshi

JR 9303 battery help

I am trying to use 1600mah NiMh battery. I am planning to cut the connector that came with Nicd battery & attach it the new battery.
I want to know which is +ve & -ve. For Tx charger that came with...
Forum: Beginners
09-18-2006, 01:54 PM
Replies: 6
Views: 1,057
Posted By schokshi

How can I conver H9 Ultra Stick 60 into Tricycle gear?

Has anybody done this before. Can I just add nosewheel & re-balance the plan leaving main gear as it is?

Thanks
09-13-2006, 11:56 AM
Replies: 3
Views: 430
Posted By schokshi

RE: Buddy Box & Battery Help

Danny,
Manual shows only 4 channels in trainer mode. Do you mean when I attach 6 channel buddy box, the screen will show 6 channels?
09-12-2006, 05:30 PM
Replies: 3
Views: 430
Posted By schokshi

Buddy Box & Battery Help

Currently I have XP642 & planning to buy 9303 PCM. Can I use XP642 as a buddy box & use all 6 cahnnels or i can only use 4 channels in trainer system? I hae H9 US 60 with flaps so I would atleast...
Forum: Beginners
09-12-2006, 11:03 AM
Replies: 3
Views: 575
Posted By schokshi

Need Help : JR Buddy Box System !!!

I have JR XP642 & XP9303. Can I use XP9303 as master & XP642 as slave & be able to control all 6 channels from XP642. 9303 manual says trainer function is only for 4 channels. That means if I have 2...
Forum: Beginners
09-02-2006, 03:43 PM
Replies: 17
Views: 910
Posted By schokshi

RE: vibrations with Saito 82

So far I have run through about 4 tanks of fuel. I have been using heli fuel because I heard Saito idles well with this fuel. I have not yet adjusted low end yet. It is still at factory setting.
Forum: Beginners
09-01-2006, 12:44 PM
Replies: 17
Views: 910
Posted By schokshi

vibrations with Saito 82

I have saito 82 mounted on H9 Ultra Stick 82 with 13x8 2 blade prop. I think hole diameter for prop is slightly larger than engine shaft diameter. When I started engine for the first time, there was...
Forum: Beginners
08-15-2006, 06:19 PM
Replies: 24
Views: 1,229
Posted By schokshi

RE: Kadet Senior retirement.

I just finished P-51 PTS ARF. If you can find an engine which will fit mount supplied with the kit then your life will be easier. I decided to put OS 70 inverted, made all necessary changes including...
Forum: Beginners
08-04-2006, 07:24 AM
Replies: 24
Views: 1,304
Posted By schokshi

RE: The "Evil" Nexstar

Hello,
I soloed about 2 months back at club called Midwest R/C Society in Northville. I also belong to another club in Canton area. I've yet to see an instructor having a preference over trainer. I...
Forum: Beginners
08-01-2006, 01:26 PM
Replies: 2
Views: 440
Posted By schokshi

RE: HANGER 9 P-51 TRAINER

I am puting one togather. I am using OS 70 4S inverted with cline regulator. ARF does come with wing foil which makes it a trainer.

This is my second plane. I soloed on LT40
Forum: Beginners
08-01-2006, 12:40 PM
Replies: 4
Views: 800
Posted By schokshi

RE: Hangar 9 PTS P-51 ARF

Currently I am assembling one togather. It is a typical ARF. You will need to hing surfaces & install radio & engine.
If you decide to use .46 size two stroke engine then there is minimum work...
Forum: Beginners
07-26-2006, 07:48 PM
Replies: 1
Views: 480
Posted By schokshi

Need help: Mounting Saito 82 inverted

I have purchased Saito 82 to use in H-9 P-51 PTS ARF. I would like to mount this engine inverted. Center line of fuel tank will be higher than spray bar. I can not modify location of fuel tank.

...
Showing results 1 to 25 of 61
 


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service - Do Not Sell My Personal Information -

Copyright 2018 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.