Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Notices
Search: Posts Made By: klord125
Showing results 1 to 13 of 13
Search took 0.02 seconds.
06-21-2020, 05:16 AM
Replies: 27
Views: 2,678
Posted By klord125

Ron, can you expand on this. Been a couple...

Ron, can you expand on this. Been a couple decades since running the boat. Not exactly sure how this should be done. Thanks Ken
06-19-2020, 11:23 AM
Replies: 27
Views: 2,678
Posted By klord125

What angle do you think the motor should be at?

What angle do you think the motor should be at?
06-10-2020, 08:03 AM
Replies: 27
Views: 2,678
Posted By klord125

Thanks Ron!!! Appreciate the help..

Thanks Ron!!! Appreciate the help..
06-09-2020, 06:30 PM
Replies: 27
Views: 2,678
Posted By klord125

Ron, Where is the 15" mark measured from on the...

Ron, Where is the 15" mark measured from on the engine?
06-09-2020, 05:26 PM
Replies: 27
Views: 2,678
Posted By klord125

I have no idea why I thought this was 48" long....

I have no idea why I thought this was 48" long. It's 45" long. Will that be a problem with a 26cc zenoah? Also have to cut out rails and glass them in. They are 4" not 5". If still ok. What do you...
06-09-2020, 08:31 AM
Replies: 27
Views: 2,678
Posted By klord125

Any idea on prop selection for this boat with a...

Any idea on prop selection for this boat with a stock Zenoah 26 cc in it? Also has The 1/4"stinger drive set up. Thanks Ken
05-22-2014, 05:35 AM
Replies: 27
Views: 2,678
Posted By klord125

Thank's again!! I like the fact I ask a question...

Thank's again!! I like the fact I ask a question and get different opinions BUT quality opinions. You guys are more helpful than you probably know to the non everyday RC boat enthusiast. It's great...
05-21-2014, 05:17 AM
Replies: 27
Views: 2,678
Posted By klord125

Thank's again guys. I have been boating for about...

Thank's again guys. I have been boating for about 20 years. Never raced though. I just like to screw around on the weekends at the camp. I have quite a few nitro boats from out boards to inboard deep...
05-20-2014, 11:37 AM
Replies: 27
Views: 2,678
Posted By klord125

Thank's guys!! Just went on there site. How is...

Thank's guys!! Just went on there site. How is there Race Pro 26 engine?
05-20-2014, 10:57 AM
Replies: 27
Views: 2,678
Posted By klord125

Thank's EC .. I think its time to restore it to...

Thank's EC .. I think its time to restore it to something useful. Where is a good place to get a decent 26cc engine from with pipe??
05-20-2014, 08:47 AM
Replies: 27
Views: 2,678
Posted By klord125

You are correct Ron. So no dissecting needed.lol...

You are correct Ron. So no dissecting needed.lol What about stuffing tubes? What size do they have to be for gas? This boat also has the old radio box that you build. Would like to upgrade to a...
05-20-2014, 08:13 AM
Replies: 27
Views: 2,678
Posted By klord125

Thanks EC !!! It hauled the mail pretty good...

Thanks EC !!! It hauled the mail pretty good with the 11cc in it.. How wide do the rails have to be to fit the gas motor?
05-20-2014, 06:40 AM
Replies: 27
Views: 2,678
Posted By klord125

48" Dumas scarab

Is this boat to small to put a gas engine in? It had an 11cc K&B in it.
Showing results 1 to 13 of 13


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service - Do Not Sell My Personal Information -

Copyright 2021 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.