RCU Forums - Search Results

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Notices
 
Search: Posts Made By: Pylonracr
Showing results 1 to 25 of 500
Search took 0.24 seconds.
Forum: RC Jets
03-23-2020, 06:49 PM
Replies: 5
Views: 907
Posted By Pylonracr

Beautiful, Thank you. Scott

Beautiful, Thank you.

Scott
02-29-2020, 07:21 PM
Replies: 13
Views: 677
Posted By Pylonracr

I don't see how the presence or absence of fabric...

I don't see how the presence or absence of fabric will affect your lung issue. That being said, ANY sanding you do should be done with a full respirator with pre filters such as we use for painting...
02-29-2020, 07:11 PM
Replies: 13
Views: 439
Posted By Pylonracr

Pretty much what I do, except I use 1 to 2 wraps...

Pretty much what I do, except I use 1 to 2 wraps of Parchment paper and lay up a couple layers of carbon fabric cut on the bias. A slightly different way of doing the same thing.

Scott
02-29-2020, 07:05 PM
Replies: 2
Views: 523
Posted By Pylonracr

Nope. That is not ribbon, what you are looking at...

Nope. That is not ribbon, what you are looking at is carbon Tow. It is strands of carbon fiber. The two have nothing in common. That being said, if you need a little bit send me a PM and I will send...
Forum: Kit Building
10-05-2019, 08:43 PM
Replies: 27
Views: 1,972
Posted By Pylonracr

I have been scratch building race planes for more...

I have been scratch building race planes for more decades than I care to admit. I use thin and medium ca for all balsa joints and epoxy for all hardwood. I use only laminating resin and not garbage...
08-22-2019, 07:55 PM
Replies: 3
Views: 1,904
Posted By Pylonracr

Yup, that is where I get all of my hot rod props....

Yup, that is where I get all of my hot rod props.

Scott
Forum: RC Jets
08-09-2019, 07:43 PM
Replies: 29
Views: 5,598
Posted By Pylonracr

Talking Speaking of getting that F14 of yours...

Speaking of getting that F14 of yours flying...............

Scott
Forum: Kit Building
07-30-2019, 08:05 PM
Replies: 11
Views: 935
Posted By Pylonracr

OK, So these 2 clowns walk into a...

OK, So these 2 clowns walk into a bar...............
Forum: Kit Building
07-26-2019, 06:07 AM
Replies: 11
Views: 935
Posted By Pylonracr

Cool, I have been using that resin for a while...

Cool, I have been using that resin for a while now and really like it. It does benefit from a post cure of 100 to 110F, especially if you use the slow catalyst. Did you figure the carbon gear out? ...
Forum: Kit Building
07-25-2019, 06:51 PM
Replies: 11
Views: 935
Posted By Pylonracr

As much as it pains me to admit it, I have to...

As much as it pains me to admit it, I have to agree with Shawn. I will add one detail though. Be sure to cut your fabric on the bias at + - 45. This will maximize the strength gained with the...
Forum: MVVS Support
05-21-2019, 07:42 PM
Replies: 22
Views: 917
Posted By Pylonracr

Somebody correct me if I am wrong. I seem to...

Somebody correct me if I am wrong. I seem to recall reading recently that Pe Reivers has passed....

Scott
05-18-2019, 06:32 PM
Replies: 4
Views: 1,173
Posted By Pylonracr

Nice. My test stand is a piece of plywood with a...

Nice. My test stand is a piece of plywood with a Dub Jett mount on it. A couple of pieces of wood and some foam hold an old fuel tank to it, and a couple more pieces of wood hold the end of the tuned...
05-18-2019, 05:49 PM
Replies: 377
Views: 43,681
Posted By Pylonracr

Well Ken, maybe we can teach Shawn something...

Well Ken, maybe we can teach Shawn something after all. A big glow 2 stroke with a pipe is just what that ugly plane needs, at least it would sound cool. Still ugly, but at least it would not sound...
05-17-2019, 07:44 PM
Replies: 377
Views: 43,681
Posted By Pylonracr

I wasn't going to go quite that far, but now that...

I wasn't going to go quite that far, but now that you mention it............

Scott
Forum: Aerodynamics
05-17-2019, 07:40 PM
Replies: 3
Views: 502
Posted By Pylonracr

As much as it pains me to agree with Shawn, I...

As much as it pains me to agree with Shawn, I have to ride along here. This request could be for something as helpful as searching for missing children in the forest or use by a terrorist. Without...
05-16-2019, 06:56 PM
Replies: 377
Views: 43,681
Posted By Pylonracr

Well Shawn, at least you have broken your string...

Well Shawn, at least you have broken your string of second place finishes....

Scott
05-05-2019, 06:57 PM
Replies: 111
Views: 19,719
Posted By Pylonracr

In other words, build a Stik. Scott

In other words, build a Stik.

Scott
05-04-2019, 07:44 PM
Replies: 111
Views: 19,719
Posted By Pylonracr

I waited 5 or 6 years before I gave up. I wanted...

I waited 5 or 6 years before I gave up. I wanted to see what all the hype was about. Apparently it was all about nothing. I have a dozen planes that will fly circles around this thing. For a...
Forum: Glow Engines
05-03-2019, 07:31 PM
Replies: 31
Views: 1,047
Posted By Pylonracr

Anytime Shawn. Tell Trixie hi for me. ...

Anytime Shawn. Tell Trixie hi for me.

Jesse, I can't comment on what oil NASCAR engines use since I have never built one.
I can't comment on what oil Indy cars use due to VERY strict...
Forum: Glow Engines
05-03-2019, 10:45 AM
Replies: 31
Views: 1,047
Posted By Pylonracr

How about me Shawn, Do you know me???? Scott

How about me Shawn, Do you know me????

Scott
Forum: Glow Engines
05-03-2019, 07:02 AM
Replies: 31
Views: 1,047
Posted By Pylonracr

Wow, long post. Part of me wants to point out...

Wow, long post. Part of me wants to point out how inaccurate your "Oil for racing and street engines" tirade is, but the sensible part of me is not going to because I do not want to hijack this...
05-02-2019, 07:43 PM
Replies: 6
Views: 933
Posted By Pylonracr

US Composites is a good source for many things. ...

US Composites is a good source for many things. Their 635 resin is my go to choice for most lamination and gluing.

Scott
Forum: Glow Engines
05-02-2019, 06:26 AM
Replies: 31
Views: 1,047
Posted By Pylonracr

Interesting comment. Care to elaborate a little??

Interesting comment. Care to elaborate a little??
04-24-2019, 07:25 AM
Replies: 377
Views: 43,681
Posted By Pylonracr

Shawn, Call Me. I will bring you some Carbon to...

Shawn, Call Me. I will bring you some Carbon to make your gear legs out of on Saturday when we come up.

Scott
Forum: Sport Flying
04-15-2019, 07:52 PM
Replies: 10
Views: 1,043
Posted By Pylonracr

For race planes we typically use low rates for...

For race planes we typically use low rates for racing but need high rates to have enough travel to land and take off.

Scott
Showing results 1 to 25 of 500
 


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service - Do Not Sell My Personal Information

Copyright 2018 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.