Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Notices
Search: Posts Made By: rpw612
Showing results 1 to 16 of 16
Search took 0.22 seconds.
03-01-2021, 07:19 PM
Replies: 0
Views: 190
Posted By rpw612

Airtronics receiver

Hello,
Does anyone know where I can get an Airtronics 92186Z pcm receiver?

Thank You,
Rick
Forum: Marketplace
03-19-2019, 04:59 AM
Replies: 2
Views: 246
Posted By rpw612

Yes it is.

Yes it is.
Forum: Marketplace
03-17-2019, 07:28 AM
Replies: 2
Views: 246
Posted By rpw612

32-10 Xoar Prop

Brand new never mounted but drilled for DA-150.
Decided to go with different prop.
Forum: Gas Engines
09-14-2018, 06:02 PM
Replies: 5
Views: 524
Posted By rpw612

Thank you again, basically asked in other forum...

Thank you again, basically asked in other forum of you put brass inline.
Forum: Gas Engines
09-14-2018, 05:44 PM
Replies: 5
Views: 524
Posted By rpw612

Thanks truckracer, saw your other post, trying to...

Thanks truckracer, saw your other post, trying to touch all bases. Like I said on the other forum I’m concerned about it bending back on itself with the klunk on.

Thank you again
Forum: Gas Engines
09-14-2018, 05:26 PM
Replies: 5
Views: 524
Posted By rpw612

Fuel tubing

Hello,

Does anyone have an opinion on the Sullivan pro flex fuel tubing, for inside and outside the tank.
know about Viton but think it might be to flexible to be used as a pick up line with the...
10-13-2016, 08:09 AM
Replies: 15
Views: 1,383
Posted By rpw612

TomCrump, I'm not to familiar with clear...

TomCrump,

I'm not to familiar with clear coats. Your knowledge is appreciated.
Would brushing on the waterborne clear show brush stokes on solartex?
Wondering about a satin finish.
Trust your...
10-12-2016, 11:30 AM
Replies: 15
Views: 1,383
Posted By rpw612

Thank you, If they don't put it in aerosol...

Thank you,

If they don't put it in aerosol cans would a badger 400 touch up gun suffice?
10-12-2016, 10:10 AM
Replies: 15
Views: 1,383
Posted By rpw612

I assume they have a satin additive, and this is...

I assume they have a satin additive, and this is applied with a spray gun only.
Does one just go to any auto part store that mixes paint?

Thanks for your patience
10-11-2016, 05:25 PM
Replies: 15
Views: 1,383
Posted By rpw612

TomCrump, What spray clear satin would you...

TomCrump,

What spray clear satin would you suggest that is gasoline fuel proof and doesn't yellow over time?

Many Thanks
10-10-2016, 02:37 PM
Replies: 15
Views: 1,383
Posted By rpw612

Gas fuel proofing

Hello,

Trying to make a decision, in clear coating a Solartex covered bipe.

Which would you choose; Polycrylic Minwax Aerosol Satin clear, or Krylon Colormaster Aerosol Satin clear?

Any and...
Replies: 8
Views: 1,107
Posted By rpw612

RE: Magnets and a 2.4 FASST

Also, I asume this holds true even with a large gas engine w/ignition (da150). Thanks again.
Replies: 8
Views: 1,107
Posted By rpw612

Replies: 8
Views: 1,107
Posted By rpw612

Magnets and a 2.4 FASST

Hello, Do magnets (rare earth magnets 3/16" dia.) to help hold a cowl in place on a giant scale plane effect the radio? Thanks to all
09-12-2010, 10:51 AM
Replies: 7
Views: 948
Posted By rpw612

RADIO INTERFERENCE

Hello, Does anyone know if using magnets as an added hold down for a COWL will cause radio interference?
Radio is a 12c fasst, and the engine is gas. Thank You to all.
04-27-2010, 08:37 AM
Replies: 1
Views: 449
Posted By rpw612

Batteries

Do the new Eneloop 5c (6v) batteries need a voltage regulator if after charging thay reach close to 7v? Thank You.
Showing results 1 to 16 of 16


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service - Do Not Sell My Personal Information -

Copyright 2021 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.