RCU Forums - Search Results

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Notices
Search: Posts Made By: jdc442
Showing results 1 to 13 of 13
Search took 0.62 seconds.
11-28-2020, 04:54 PM
Replies: 4
Views: 1,607
Posted By jdc442

I heard it trip the gfci in my garage when I...

I heard it trip the gfci in my garage when I turned the power supply on with nothing on it but the dial turned up to 24v. I'm charging no more than 1c on 2 channels so about 6.5 amp each side. It...
11-28-2020, 03:57 PM
Replies: 4
Views: 1,607
Posted By jdc442

Tripping various breakers in my house

I am currently using the evpeak pj1 with the icharger duo 406 and I seem to trip various breakers throughout my house. I feel like it trips when I first turn on the power supply. I have the dial...
Forum: Glow Engines
11-04-2005, 10:27 AM
Replies: 0
Views: 353
Posted By jdc442

collari .32 carb swap

i have an old rb concept c4 engine that doesn't run anymore and have heard people swapping the carb out on the collari .32, i am just curious if the carb from the c4 will work on the .32? it seems to...
10-31-2005, 09:47 AM
Replies: 5
Views: 571
Posted By jdc442

RE: hitec steering servo

i've had the 645mg with negative results, for some reason my servo gets tweaked to one direction and it won't center, i thought it might be slipping on the spline or something but the threads look ok
10-28-2005, 09:53 PM
Replies: 5
Views: 571
Posted By jdc442

RE: hitec steering servo

no actually i got it from servocity.com, i haven't found it cheaper than $115, appearantly the robotic one rotates 180 degrees and the the other one rotates 90 degrees, with the average servo rotates...
10-28-2005, 09:15 PM
Replies: 5
Views: 571
Posted By jdc442

hitec steering servo

i just ordered the hitec hs(r)-5955tg for my steering servo on my savage, well i noticed that this one is for robots and didn't know there is another one hs(c)-5955tg thats is advertised for 1/4...
10-09-2005, 07:24 PM
Replies: 6,159
Views: 703,084
Posted By jdc442

RE: PICS OF YOUR SAVAGES !!

here is my rig w/ 1.5" ext tvps

http://img.photobucket.com/albums/v398/gasman442/Savage001.jpg

http://img.photobucket.com/albums/v398/gasman442/Savage004.jpg
10-09-2005, 11:51 AM
Replies: 5
Views: 459
Posted By jdc442

RE: clutchbell install problem

ok thank you, i overlooked the shim kit, i wasn't aware there were spacers to add lengths, i only thought there were shims, appreciate you clarifying
10-07-2005, 08:06 PM
Replies: 5
Views: 459
Posted By jdc442

RE: clutchbell install problem

thanks for the reply but my prolem is not adding length its that i am too long, my cb sticks out too far past the end of the shaft, i need to shorten my length up somewhere, i might try trimming the...
10-07-2005, 10:02 AM
Replies: 5
Views: 459
Posted By jdc442

clutchbell install problem

i am installing an ofna 16t cb on my collari .32 w/ the werks racing clutch, i used the collet from an rc10gt so i wouldn't have to shim, well i have the adjusting nut to engage earlier which means...
09-15-2005, 08:05 AM
Replies: 16
Views: 1,216
Posted By jdc442

RE: collari .32

shop around u can find this engine for $200, some places have them pretty steep, i snagged mine off ebay for like $210 shipped
09-14-2005, 11:38 AM
Replies: 20
Views: 1,033
Posted By jdc442

RE: Got a Collari .32

for those of you having trouble with the clutch fitting on, (especially the werks racing clutch) the flywheel sits too deep on the collet therefor the clutch nut only buts up to the collet leaving...
09-13-2005, 11:30 AM
Replies: 1
Views: 433
Posted By jdc442

werks racing clutch on collari .32

i am trying to install the werks racing clutch on the collari .32 and i can't seem to get the flywheel tight on the crankshaft even when i tighten the long nut that goes on after...it seems like i...
Showing results 1 to 13 of 13


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service - Do Not Sell My Personal Information -

Copyright 2021 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.