Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Notices
 
Search: Posts Made By: RTK
Showing results 1 to 25 of 500
Search took 0.73 seconds.
Forum: Gas Engines
02-03-2013, 08:13 PM
Replies: 222
Views: 42,608
Posted By RTK

RE: Two Cycle Oil for Air Cooled Engines

You don't need any oil after you treat with proloooong:)
Forum: Gas Engines
11-15-2012, 12:39 PM
Replies: 6
Views: 648
Posted By RTK

RE: G62 Cunningham Conversion

Make sure the externa pulse line isn't cracked or plugged, make sure you put the diaphragm on first then the gasket to wards the carb body, clean all passages out with carb cleaner first.
Forum: Gas Engines
11-15-2012, 12:00 PM
Replies: 6
Views: 648
Posted By RTK

RE: G62 Cunningham Conversion

Dennis, open up the pump side of the carb and put some fuel there. Sometimes the pump side won't work until it gets wet. Prime the engine also to get it running and all should be fine.
One last...
Forum: Gas Engines
11-15-2012, 08:36 AM
Replies: 23
Views: 2,015
Posted By RTK

RE: BME 116 how different than 115?

Yep, I still have one of the first two of the 110 and 116. The 110 has to be about 10 years old now. There are many good engines on the market now, BME being one of the good one:)
Forum: Gas Engines
11-14-2012, 08:31 PM
Replies: 23
Views: 2,015
Posted By RTK

RE: BME 116 how different than 115?

Most two strokes are low compression so high octane is not of much use. With some of the higher compression 2 strokes it can be and is beneficial. The one thing I can guarantee is, if you are lean...
Forum: Gas Engines
11-01-2012, 07:46 AM
Replies: 23
Views: 2,015
Posted By RTK

RE: BME 116 how different than 115?

I would use high octane or avgas if available.
Forum: Gas Engines
05-11-2012, 02:42 PM
Replies: 49
Views: 9,304
Posted By RTK

RE: DLE-30 Carb Wont Draw Fuel

Too much air is passing from somewhere if the butterfly is closed and it is still running, especially at that high of rpm
Forum: Gas Engines
05-04-2012, 08:26 AM
Replies: 49
Views: 9,304
Posted By RTK

RE: DLE-30 Carb Wont Draw Fuel

Take a blunt object, pressurize the tank, then push on the diaphragm through the vent hole, fuel will flow, if it doesn't you have your answer.
Forum: Gas Engines
05-03-2012, 06:08 PM
Replies: 49
Views: 9,304
Posted By RTK

RE: DLE-30 Carb Wont Draw Fuel

Nothing better than a fresh pan sized trout on the plate
Forum: Gas Engines
05-03-2012, 05:50 PM
Replies: 49
Views: 9,304
Posted By RTK

RE: DLE-30 Carb Wont Draw Fuel

The metering needle could possibly be stuck, even a mal-adjusted fulcrum arm wouldn't stop the fuel from flowing when choked. You did open the needles after rebuilding. right?
When assembling the...
05-03-2012, 03:55 PM
Replies: 188
Views: 26,870
Posted By RTK

RE: LA7 Info / Research / Build - Scale Wings

Louvers do a great job of extracting air. Most people don't realize that is probably the most important part of air flow, create a good low pressure area to move all that hot air out.
Trying to...
05-03-2012, 03:34 PM
Replies: 188
Views: 26,870
Posted By RTK

RE: LA7 Info / Research / Build - Scale Wings

Don't forget to post some pics of your handy work
05-03-2012, 03:27 PM
Replies: 188
Views: 26,870
Posted By RTK

RE: LA7 Info / Research / Build - Scale Wings

What did that set you back, and how well will it work
Forum: Gas Engines
05-03-2012, 03:19 PM
Replies: 49
Views: 9,304
Posted By RTK

RE: DLE-30 Carb Wont Draw Fuel

Hmmm, you could be right.
All you need to make an engine run is spark, fuel and air. We know air is there so all you have to do is find out which one is missing to diagnose the problem and go...
Forum: Gas Engines
05-03-2012, 02:59 PM
Replies: 49
Views: 9,304
Posted By RTK

RE: DLE-30 Carb Wont Draw Fuel

Apparently it is pumping fuel after rebuild, something not right here.
Forum: Gas Engines
05-03-2012, 01:45 PM
Replies: 8
Views: 1,146
Posted By RTK

RE: G62 muffler install, need advise Please.....

The pipe might or might not change the performance of the engine. I still would run a straight pipe if noise is not a problem, you can't use JB weld and instead of solder use braze. It isn't that...
Forum: Gas Engines
05-03-2012, 01:37 PM
Replies: 49
Views: 9,304
Posted By RTK

RE: DLE-30 Carb Wont Draw Fuel

Thing is you have fuel in the carb as stated before so it is pumping. Time to start looking on the ignition side if you can't get it to pop. As captain mentioned a little more info would help
Forum: Gas Engines
05-03-2012, 12:13 PM
Replies: 49
Views: 9,304
Posted By RTK

RE: DLE-30 Carb Wont Draw Fuel

Pulse line?? Dry carb??
Forum: Gas Engines
05-03-2012, 11:42 AM
Replies: 8
Views: 1,146
Posted By RTK

RE: G62 muffler install, need advise Please.....

Run a straight pipe right out the bottom, it will sound better too
Forum: Gas Engines
05-03-2012, 11:36 AM
Replies: 16
Views: 5,799
Posted By RTK

RE: Checkvalve replacement on Walbro wj-71

I didn't think the check valve was all that important, isn't it just to stop some richening when backing off of the throttle.
Forum: Gas Engines
05-03-2012, 11:30 AM
Replies: 49
Views: 9,304
Posted By RTK

RE: DLE-30 Carb Wont Draw Fuel

Did you reassemble the carb correctly?? Also check the reeds and the pulse line holes to make sure they are lined up, they do run an internal pulse line right??
Forum: Gas Engines
05-03-2012, 10:49 AM
Replies: 9
Views: 959
Posted By RTK

RE: Does DA make a high performance version of their engines?

He would polish the exhaust port, change the base gaskets to better sinc the port timing and go thru the carb. It really didn't increase power to any degree, but runability. I believe it was Salsa...
Forum: Gas Engines
05-02-2012, 07:38 PM
Replies: 9
Views: 959
Posted By RTK

RE: Does DA make a high performance version of their engines?

They have a magnesium and cylinder lightened version of the 200, but no, they have nothing but stock. That does not stop you from modifying them yourself, change port timing, squish and squish angel,...
Forum: Glow Engines
05-02-2012, 07:12 PM
Replies: 32
Views: 2,775
Posted By RTK

RE: Ring Engine Compression

That pretty much covers it
Showing results 1 to 25 of 500
 


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service - Do Not Sell My Personal Information -

Copyright 2018 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.