RCU Forums - Search Results

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Notices
Search: Posts Made By: moki180
Showing results 1 to 15 of 15
Search took 0.42 seconds.
09-06-2012, 07:37 AM
Replies: 11
Views: 4,587
Posted By moki180

RE: Gee Bee R4

Have you flown yours yet? I just ordered mine looking for any problems you might of had

Frank
Forum: RC Jets
03-13-2011, 11:17 AM
Replies: 42
Views: 5,321
Posted By moki180

RE: Santa finally arrived with my beer! ** Started Building **

Built a tank tray and replaced the middle bulkhead to have room for 2 x 20 oz smoke tanks, main tank dubro 100oz is centered on the cg . The tray is end grain balsa sheeted with 64 ply very rigid...
Forum: RC Jets
02-21-2011, 04:05 PM
Replies: 42
Views: 5,321
Posted By moki180

RE: Santa finally arrived with my beer! ** Started Building **

I have my own sign company,so I can print just about anything, I usually don't clear coat its pretty durable it haven't had problems yet i have planes 10 years old and the still look good.

...
Forum: RC Jets
02-20-2011, 06:43 PM
Replies: 42
Views: 5,321
Posted By moki180

RE: Santa finally arrived with my beer! ** Started Building **

too bad its a little chilly -35 so this weekend I spent some time finishing up the decals I wanted the same logo layout but with my own touch making it a custom and what I think it would look today .
Forum: RC Jets
02-17-2011, 10:09 AM
Replies: 42
Views: 5,321
Posted By moki180

RE: Santa finally arrived with my beer! ** Started Building **

I read in another post that CG should be 4 3/4 from LE can anyone confirm this or is this a good starting point.

Frank
Forum: RC Jets
02-17-2011, 06:58 AM
Replies: 42
Views: 5,321
Posted By moki180

RE: Santa finally arrived with my beer! ** Started Building **

If I put my bell mouth under the lip my turbine is not centered in the pipe and placing it even further back behind the lip, won't it start causing air flow problems around the bell mouth? I don't...
Forum: RC Jets
02-16-2011, 09:03 AM
Replies: 42
Views: 5,321
Posted By moki180

RE: Santa finally arrived with my beer! ** Started Building **

I placed my rabbit where I think it should go and used a measurement of 1" from the turbine exhaust to the start of the tail pipe does this look right with the bell housing extending pass the lip?
...
Forum: RC Jets
02-04-2011, 07:31 AM
Replies: 42
Views: 5,321
Posted By moki180

RE: Santa finally arrived with my beer! ** Started Building **

Does any one have pics of engine installations I not sure on what to use, the rabbit fits nice but the P80 seems bulky any won't fit till the rails are open up .This is my first jet with an exhaust...
Forum: RC Jets
01-28-2011, 06:04 PM
Replies: 185
Views: 58,154
Posted By moki180

RE: BD-5J Project

Today I was pleasantly surprised when my bd5 arrived today which is now sitting on my kitchen island,its been a long 4 months . I been following the forum for awhile and noticing that the finishing...
Forum: RC Jets
11-15-2010, 10:52 AM
Replies: 185
Views: 58,154
Posted By moki180

RE: BD-5J Project

Has any one looked at the indecent of wing or stab when the plane sits on its gear to correct the take-off problem ,also would a full flying stab like the real one change anything?

Frank
Forum: RC Jets
11-13-2010, 06:04 PM
Replies: 185
Views: 58,154
Posted By moki180

RE: BD-5J Project

What is the reasoning for not using a bigger turbine ,I understand the thrust issues with the plane which should be able to mixed out mostly in today's radio systems all I am trying to do is get the...
Forum: RC Jets
11-13-2010, 11:28 AM
Replies: 185
Views: 58,154
Posted By moki180

RE: BD-5J Project

On the fence right now, I want to fly off grass most of the time and the p80 se although heavier than the rabbit has 3 more lbs thrust.

Frank
Forum: RC Jets
11-12-2010, 02:46 PM
Replies: 185
Views: 58,154
Posted By moki180

RE: BD-5J Project

I was told 5-6 wks in the Coors scheme with out lettering I will be making my own,hopefully between us we should be able to figure the instruction dilemma plus I have a few mod ideas from what I...
Forum: RC Jets
11-12-2010, 12:39 PM
Replies: 185
Views: 58,154
Posted By moki180

RE: BD-5J Project

I also just order mine last week not realizing that there are no instructions included and I will be watching closely for any info posted

Cheers,
Frank
Forum: Kit Building
11-24-2008, 03:26 PM
Replies: 8
Views: 5,252
Posted By moki180

RE: Unionville 1/4 scale Beaver kit builders

A friend put me onto this forum I have a 1/4 beaver that i bought used and rebuilt it from the gound up I got it flying this summer and I keep adding more scale things as time goes on it keeps...
Showing results 1 to 15 of 15


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service - Do Not Sell My Personal Information -

Copyright 2021 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.