Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Notices
Search: Posts Made By: GeeBee Commander
Showing results 1 to 14 of 14
Search took 0.60 seconds.
11-21-2005, 08:08 AM
Replies: 15
Views: 859
Posted By GeeBee Commander

RE: X1CR Shock Problem

The side cutters did not prevent the shaft from turning. They provided some traction, the plastic piece was hard to turn, but it moved the shaft too. The side cutters just made a little gouge in the...
11-20-2005, 03:58 PM
Replies: 15
Views: 859
Posted By GeeBee Commander

RE: X1CR Shock Problem

I still can not get it to loosen. Is there anything else I should try, or should I just let it be incorrect?
11-19-2005, 10:12 AM
Replies: 15
Views: 859
Posted By GeeBee Commander

X1CR Shock Problem

I was just building the shocks on my X1CR and found that I had tightened the black plastic thing, in the instruction manual it is called the "shock plastic rod end", more than I was supposed to onto...
05-24-2005, 09:06 AM
Replies: 5
Views: 451
Posted By GeeBee Commander

RE: Servo question

The J-connector has the fin, but it is very easy to strip off.
03-31-2005, 09:59 AM
Replies: 7
Views: 768
Posted By GeeBee Commander

RE: Kani 3 vs. x1cr also titanium

What about the x1cr vs. Kanai 3...
I know people are tired of the "which is better" question so advantages and disadvantages would be good.

Titanium: It is therefore useless to have parts...
03-31-2005, 09:54 AM
Replies: 8
Views: 615
Posted By GeeBee Commander

Starter box

What is a very good starter box that is cheap? Lots of people recommend the Ofna chrome top which is $69 at tower ($98 with battery and charger) but I don't want to spend that much.
03-30-2005, 04:39 PM
Replies: 7
Views: 768
Posted By GeeBee Commander

Kani 3 vs. x1cr also titanium

Is the Kanai 3 better than the x1cr? Any big differences?
Is titanium better than aluminum for racing?
I know that titanium is stronger than aluminum but it is heavier.
02-09-2005, 09:58 AM
Replies: 1
Views: 387
Posted By GeeBee Commander

OPS pipe

Does anyone know anything about the OPS op37950 pipe? Does it increase low end? mid end? high end? Is OPS a good company overall? Just wondering.
01-14-2005, 03:33 PM
Replies: 2
Views: 449
Posted By GeeBee Commander

plz help: Diff and shock fluid for MP777 standard

What weight diff and shock fluid should I use?
I have a Kyosho MP777 standard and use an Ofna Hyper .21 8-Port Race Engine.
12-31-2004, 01:41 PM
Replies: 10
Views: 631
Posted By GeeBee Commander

RE: ultra lx comp steering servo

I was thinking about the hitec 645mg. Some people say that hitec servos are bad, but what else is there for around $40?
12-31-2004, 09:45 AM
Replies: 3
Views: 1,264
Posted By GeeBee Commander

RE: Hobbico or Hitec servo?

one more thing...

Will the Ofna micro failsafe (with a futaba J connector) work with either of these servos and the radio?
12-31-2004, 09:39 AM
Replies: 3
Views: 1,264
Posted By GeeBee Commander

Hobbico or Hitec servo?

I'm looking for a steering servo for Airtronics MX-3S 3-Channel FM/1 94102Z Servo 75MHz

The Hobbico CS-70MG Servo Super Torque 2BB U and the Hitec HS-645MG High-Torque 2BB MG Servo...
12-30-2004, 01:46 PM
Replies: 14
Views: 793
Posted By GeeBee Commander

RE: is 85 oz in of torque enough for a MP777?

I'm yub yub's friend... this post is no longer useful so you can stop posting about servos. By the way are anti lock brakes (ABS) needed for a buggy?
Showing results 1 to 14 of 14


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service - Do Not Sell My Personal Information -

Copyright 2018 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.