Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Notices
 
Search: Posts Made By: Edge 540
Showing results 1 to 25 of 321
Search took 0.64 seconds.
11-11-2008, 10:13 PM
Replies: 3
Views: 756
Posted By Edge 540

RE: FlyCam ?

have you tried going to my computer? It should show up there and as lejongleur said you can copy and paste to your desktop or anywhere else that is convenient.
11-11-2008, 05:49 PM
Replies: 7
Views: 927
Posted By Edge 540

RE: Yak 54 101!

Flaperons and a lot of sliding in sideways for landing!
If there's enough wind just letting it drop with as little forward speed as possible is also an option.
11-09-2008, 08:47 PM
Replies: 7
Views: 927
Posted By Edge 540

RE: Yak 54 101!

It has TONS of power. I'm not kidding, I did a vertical drag race with a 3D profile and kept up with it for the first several hundred feet. This plane will hover no problem at all.
The power is...
11-09-2008, 02:10 PM
Replies: 7
Views: 927
Posted By Edge 540

11-09-2008, 12:38 PM
Replies: 7
Views: 927
Posted By Edge 540

11-09-2008, 12:32 PM
Replies: 7
Views: 927
Posted By Edge 540

11-09-2008, 12:01 PM
Replies: 7
Views: 927
Posted By Edge 540

Yak 54 101!

Here's my rig and a few pics:
-Yak 54 101! (8' telemaster)
-Hacker A60-20S
-10 cell lipos
- Canon point and shoot and/or Nikon N90S film SLR
08-15-2008, 03:45 PM
Replies: 8
Views: 1,682
Posted By Edge 540

RCAPA

Are the forums gone? I havent looked for about a year. What happened?
Replies: 2
Views: 622
Posted By Edge 540

RE: Are Fut S9451 Digital Servos OK ?

Yep, they are top of the line heli servos. Not exclusively heli, but they are perfect for that application. SUPER FAST!
Forum: Glow Engines
06-02-2007, 10:11 PM
Replies: 10
Views: 2,695
Posted By Edge 540

RE: Saito 82 needle settings

That makes sense. I do prime it quite a bit... Thanks.
Forum: Glow Engines
05-31-2007, 01:45 PM
Replies: 10
Views: 2,695
Posted By Edge 540

RE: Saito 82 needle settings

Could the backward running problem have something to do with the rocker arm spacing? I never re-adjusted after breaking in. I doubt most people do though...
Forum: Glow Engines
05-30-2007, 02:30 PM
Replies: 10
Views: 2,695
Posted By Edge 540

RE: Saito 82 needle settings

My 82 likes to start backward. It will idle, transition, full throttle and everyting all while running backward. Other than that it runs great. Is it a tuning issue?
Also I have been breaking...
05-04-2007, 06:33 PM
Replies: 21
Views: 4,473
Posted By Edge 540

RE: Today's Aiptek 1.3 aerial pic's

HAHA I was looking at those and thinking "Man thats just like my field." WAIT I know those cars!
Forum: 3D Flying!
02-03-2007, 10:49 PM
Replies: 7
Views: 674
Posted By Edge 540

RE: 3102's in OMP Boxxer?

Everyone, keep in mind that these servos are metal geared. I am about to use them in a larger non aerobatic model. No testing gas been done, but they seem rock solid, very light and have the same...
Replies: 28
Views: 2,618
Posted By Edge 540

RE: Most popular channel on 72 mhz????

46 seems to be very popular in my experience.
01-20-2007, 07:18 PM
Replies: 24
Views: 3,818
Posted By Edge 540

RE: crash film from holland

I really like the Rutan Quickie!
Forum: Glow Engines
01-18-2007, 12:34 AM
Replies: 3
Views: 551
Posted By Edge 540

OS120AX exhaust port

Why is the front 1/5 of the exhaust port sealed on the new 120AX? I would assume that it would be left open as much as possible, and the restriction be done in the muffler (or not done) to improve...
Forum: The Clubhouse
01-18-2007, 12:30 AM
Replies: 26
Views: 2,059
Posted By Edge 540

RE: Is It Just Me ?

I have found that it depends on which service they use for shipping. When I order something large, it goes UPS and is here in 2 days. The last two orders were small pieces and came USPS and took...
Replies: 21
Views: 3,869
Posted By Edge 540

RE: Brushless Servos

Thanks. This is exactly the type of discussion I was looking for a year ago. Any hypotheses on what specifically futaba is releasing as a brushless motor in the new servos? Speculation on current...
Forum: Aerodynamics
12-23-2006, 05:09 PM
Replies: 590
Views: 38,549
Posted By Edge 540

RE: Can It Take Off??

Great...it came back! [sm=redface.gif]
Replies: 21
Views: 3,869
Posted By Edge 540

RE: Brushless Servos

Ok, a few years ago I was thinking about the question of brushless servos and finally got around to posting it a little over a year ago. Futaba now offers brushless digital servos. Anyone know how...
12-04-2006, 01:55 PM
Replies: 31
Views: 2,844
Posted By Edge 540

RE: Viper 500

Nice.
When I did my research project I did everything in metric as well.
12-04-2006, 10:35 AM
Replies: 14
Views: 5,126
Posted By Edge 540

RE: S9351 Digital Servo vvviiiibbbrrraaatttiiinngg

Tower's website is flawed. Put S9155 in the search box and you will find them. It has to have the S too, because 9155 produces nothing. Tower has the best website layout by far of any RC...
12-04-2006, 01:05 AM
Replies: 31
Views: 2,844
Posted By Edge 540

RE: Viper 500

Actually, I start the plane on a bench so the initial altitude is higher than the takeoff and landings. You can even see a little spike where the spotter lifted the plane vertically over his head to...
12-04-2006, 12:52 AM
Replies: 31
Views: 2,844
Posted By Edge 540

Showing results 1 to 25 of 321
 


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service - Do Not Sell My Personal Information -

Copyright 2018 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.