RCU Forums - Search Results

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Notices
Search: Posts Made By: serendpt
Showing results 1 to 11 of 11
Search took 0.59 seconds.
10-03-2021, 10:24 AM
Replies: 4
Views: 3,539
Posted By serendpt

Thanks for the advice, I'll give them a whirl...

Thanks for the advice, I'll give them a whirl over the coming week. Hopefully I'll get these running soon and will find a decent model to put them in.
09-30-2021, 11:15 PM
Replies: 4
Views: 3,539
Posted By serendpt

Servicing unused diesels

Several years ago I had bought a few Sharma diesels (1.5cc and 3.2cc) just for the heck of it. I didn't think I'd be able to get them to run as we don't have access to model diesel fuel or the raw...
09-05-2005, 08:22 PM
Replies: 18
Views: 1,760
Posted By serendpt

RE: Can anyone recommend a F/F design for a Cox Black Widow?

As you can see, I have precious little experience with free flight :) It's been a good twenty years or more since I flew rubber models. Back then, every field was a candidate, and if it turned out to...
09-05-2005, 04:55 AM
Replies: 18
Views: 1,760
Posted By serendpt

RE: Can anyone recommend a F/F design for a Cox Black Widow?

I was aware of the prop trick but didn't think about the extra head gaskets. What material can these be made from, should I not be able to source any locally? I haven't opened this engine up yet so...
09-04-2005, 01:07 PM
Replies: 18
Views: 1,760
Posted By serendpt

Can anyone recommend a F/F design for a Cox Black Widow?

I recently acquired a Cox Black Widow that I'd like to put into a free flight model. I'm looking for something relatively easy to build and won't fly too fast. Perhaps even an old timer design would...
01-17-2005, 11:38 PM
Replies: 920
Views: 206,509
Posted By serendpt

RE: 1/2A trainer anyone?

Andrew,

I am using the gif file (which I had printed) from the 1/2A All the Way site, as well as referring to the PDF file from the same site. You'll have to excuse my ignorance as far as being...
01-17-2005, 09:51 PM
Replies: 920
Views: 206,509
Posted By serendpt

RE: 1/2A trainer anyone?

Yes, Andrew, that was a great help. Thanks a bunch! It didn't occur to me the wingtip was at an angle. I thought the top spars were cut at an angle and went down to the wingtips.

Moving on to...
01-17-2005, 07:42 AM
Replies: 920
Views: 206,509
Posted By serendpt

RE: 1/2A trainer anyone?

I agree with Bruce, this plan is worth being a sticky. I feel it could be a great model for first time builders and flyers. What I'd really love to see is this thread become a construction article...
Forum: ARF or RTF
05-03-2004, 04:38 AM
Replies: 0
Views: 361
Posted By serendpt

Fuel tank installation on Super Frontier

I have a World Models Super Frontier 20 and was wondering if anyone could give me some advice. According to the manual, the fuel tank for this aircraft is just shoved into the tank bay, and secured...
01-06-2004, 01:43 AM
Replies: 6
Views: 3,099
Posted By serendpt

RE: Inches to milimeters

Thanks, everyone. I guessed as much it would be ok, but it gives me peace of mind to get the go ahead from experienced builders such as yourselves. :D
12-23-2003, 05:14 PM
Replies: 6
Views: 3,099
Posted By serendpt

Inches to milimeters

Was about to try my hand at building from a plan, but immediately ran into a problem. So far, all of the balsa sheets I have found in the local (bear in mind, 'local' to me means Malaysia) hobby...
Showing results 1 to 11 of 11


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service - Do Not Sell My Personal Information -

Copyright 2021 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.