Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Notices
 
Search: Posts Made By: bmoranx
Showing results 1 to 25 of 30
Search took 0.66 seconds.
Forum: Marketplace
06-25-2019, 03:00 PM
Replies: 9
Views: 768
Posted By bmoranx

To my knowledge, there are no gen1 and gen2 DX9s....

To my knowledge, there are no gen1 and gen2 DX9s. There are gen1 and gen2 dx18s though. DX9s have a silver or black version. This is the silver version. There is no functionality differences between...
Forum: Marketplace
06-24-2019, 07:19 AM
Replies: 9
Views: 768
Posted By bmoranx

If you click on the picture, you can see the...

If you click on the picture, you can see the charger and neck strap in the picture. I am also including a brand new pelican case to ship it in. This is a pelican case and not a cheap copy. I will...
Forum: Marketplace
06-21-2019, 05:03 PM
Replies: 9
Views: 768
Posted By bmoranx

like new Spektrum DX9

Spectrum DX9 transmitter. Clean, no scratches or damage of any kind. This was a back up radio and was never used for anything other than setting up airplanes and helicopters. I replaced the original...
Forum: Marketplace
05-02-2018, 08:09 AM
Replies: 3
Views: 935
Posted By bmoranx

P-51

Can you provide me with more details? Did you assemble this or did you purchase it from someone? How much time is on the DA50? Has it been serviced? How old is the air frame? Do you have more pics?...
Forum: Marketplace
04-06-2018, 02:46 PM
Replies: 2
Views: 396
Posted By bmoranx

Your T-28

Hello Steve,

Still have your T-28 and would you take 500 for it? If so, let me know and I could pick it up tonight or tomorrow.
06-05-2008, 05:50 PM
Replies: 313
Views: 74,012
Posted By bmoranx

RE: NEW Hangar 9 85cc SU-26MM Sukhoi

Andrew - I purchased a header from RC showcase and a coupler and MTW 110 canister from DA. It is a good combo and very quiet. I really wanted to use a TR-80 from RC showcase but I knew it wouldn't...
06-04-2008, 08:30 PM
Replies: 313
Views: 74,012
Posted By bmoranx

RE: NEW Hangar 9 85cc SU-26MM Sukhoi

I have been flying my Sukhoi with a ZDZ Super 80. I lost my supersonic pitts muffler and purchased a Bisson pitts muffler. This is a nice looking muffler with a cool mounting strap feature and is...
04-17-2008, 05:44 PM
Replies: 313
Views: 74,012
Posted By bmoranx

RE: NEW Hangar 9 85cc SU-26MM Sukhoi

Inverted requires very little down elevator. I will fly it more this weekend to begin the actual trim process. When pulling long verticals, I believe it pulled slightly to the belly but I will pay...
04-17-2008, 02:30 PM
Replies: 313
Views: 74,012
Posted By bmoranx

RE: NEW Hangar 9 85cc SU-26MM Sukhoi

Hi Mike - My CG is slightly less than 8". Between 7 3/4" and 8"...
04-17-2008, 01:02 PM
Replies: 313
Views: 74,012
Posted By bmoranx

RE: NEW Hangar 9 85cc SU-26MM Sukhoi

All - I have flown mine and all seems reasonably well thus far. The day I did the maiden flight, it was fairly windy and the airplane flew extremely lite but most people would find that normal when...
03-21-2008, 11:09 AM
Replies: 313
Views: 74,012
Posted By bmoranx

RE: NEW Hangar 9 85cc SU-26MM Sukhoi

Mike - I completed this airplane with the acceptation of the pipe and all I can say is nice job man. Everything was bolted together and all travel adjustments made in less than 10 hours. I am not a...
Forum: T-Rex heli
11-17-2007, 06:01 PM
Replies: 16
Views: 1,862
Posted By bmoranx

RE: hand made t-rex case

Hey pat750r - Awesome JOB! How about posting some quick down and dirty plans and materials list for this case... I'd love to build one like yours also! What type of wood material did you use, pine?
...
11-03-2007, 12:34 AM
Replies: 8
Views: 3,251
Posted By bmoranx

RE: BLADE DANCER - MS Composit

I have the instructions but the reeaaallllyyyyy suck... The cg is 95-105 mm from the leading edge of the wing. I am starting to build mine soon but I need to know what the dang the strung is used...
Forum: Gas Engines
08-04-2007, 10:54 PM
Replies: 222
Views: 42,396
Posted By bmoranx

RE: Two Cycle Oil for Air Cooled Engines

Same here, my weed whacker and chain saw runs on old gas and cheep oil and has been doing so for over 10 years now. The only difference I see is that I really don't get as nervous when my weed...
08-04-2007, 01:03 PM
Replies: 0
Views: 1,066
Posted By bmoranx

ZDZ 80 RVJ Idle problems

All - my ZDZ 80RVJ runs well and transitions quickly and cleanly but I have one problem.... The engine idles a bit higher than I'd like. I can run it around 1800-1900 rpm with reliable and consistent...
05-09-2007, 01:30 PM
Replies: 13
Views: 2,107
Posted By bmoranx

RE: 50cc vs 75cc vs 100cc

I was also stuck with this decision. I chose to go the middle route and got an Aeroworks 75cc Yak. I powered mine with the ZDZ Super 80 and have not looked back. This airplane came in at 22lbs and...
04-16-2007, 06:54 PM
Replies: 8
Views: 1,054
Posted By bmoranx

RE: Manual for OMP 47" Edge ARF

Awesome.... Thanks for the quick response!!!

B
04-15-2007, 03:42 AM
Replies: 8
Views: 1,054
Posted By bmoranx

Manual for OMP 47" Edge ARF

Help.....

I bought an OMP 47" Edge ARF at the Toledo show but there was no manual in the box... I went to the web site and OMP does not list this airplane nor do they have any doccumentation...
03-30-2007, 09:39 AM
Replies: 9
Views: 1,134
Posted By bmoranx

throttle curve?

All – I am flying an Aeroworks 80cc Yak with a ZDZ Super80. Nice combo but the throttle response is not linear. The engine is propped correctly and rpm’s are good so I think I can fix this with a...
Forum: 3D Flying!
07-10-2006, 07:25 PM
Replies: 3,636
Views: 388,323
Posted By bmoranx

RE: Extra 260 27% Hangar 9er

If I moved it back further, I wondered if it would be more pitch poppy (quick) like a foamy?
Forum: 3D Flying!
07-10-2006, 06:05 PM
Replies: 3,636
Views: 388,323
Posted By bmoranx

RE: Extra 260 27% Hangar 9er

CG CG, where are your CG points. Mine is at 5 1/4, (the recomended limit) and it dosen't feel or fly tail heavy. I am curious how far I can go before this thing gets squirly... How far back have you...
Forum: 3D Flying!
06-20-2006, 06:03 PM
Replies: 3,636
Views: 388,323
Posted By bmoranx

RE: Extra 260 27% Hangar 9er

I agree with JuzPlaneCrazy... The 260 is a good value and flyer for the size and price range. If I splatted mine, I'd get another. I am running my 260 with a Saito 220. I just switched to a Mejzlik...
Forum: 3D Flying!
05-27-2006, 03:33 PM
Replies: 2
Views: 387
Posted By bmoranx

RE: H9 Extra 260 build help

The260 is now assembled. I will still need to mount the engine but the rest is all done. Should I permanently mount the stabs? I was also thinking about carbon wing tubes. are these available?

...
Forum: 3D Flying!
05-26-2006, 06:45 PM
Replies: 2
Views: 387
Posted By bmoranx

H9 Extra 260 build help

Hello to all...

I am building the H9 Extra 260. I Have not yet chosen an engine however I just bought a Saito 220 from a club member NIB for $380.00 so I may use that. My servos are as follows.....
Forum: 3D Flying!
05-21-2006, 08:14 AM
Replies: 3,636
Views: 388,323
Posted By bmoranx

RE: Extra 260 27% Hangar 9er

All - please state your opinion...

My I just bought a Saito 220 from a club member new in box for $380.00. I am thinking of putting this in the H9 Extra 260. I was planning on going gas but may...
Showing results 1 to 25 of 30
 


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service - Do Not Sell My Personal Information -

Copyright 2018 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.