RCU Forums - Search Results

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Notices
 
Search: Posts Made By: FUTABA-RC
Showing results 1 to 25 of 500
Search took 0.07 seconds.
03-16-2023, 09:43 PM
Replies: 2
Views: 135
Posted By FUTABA-RC

Take a look at page 190 of the manual. You should...

Take a look at page 190 of the manual. You should be able to change the switch selection
03-08-2023, 08:49 PM
Replies: 77
Views: 2,048
Posted By FUTABA-RC

Great you can get a waiver for a contest. Now,...

Great you can get a waiver for a contest. Now, how do you practice for that contest you need a waiver to fly in?
03-07-2023, 08:12 PM
Replies: 2
Views: 255
Posted By FUTABA-RC

It is done using the camber menu. I'll go into...

It is done using the camber menu. I'll go into greater detail tomorrow.
03-07-2023, 08:10 PM
Replies: 2
Views: 221
Posted By FUTABA-RC

Most of the non-S.Bus receivers are going EOL. I...

Most of the non-S.Bus receivers are going EOL. I still use some very old 617 RX. As long as they keep working no need to throw you radio away. Also, if your radio can do it the TFHSS RXs are very...
03-07-2023, 08:07 PM
Replies: 1
Views: 208
Posted By FUTABA-RC

Not sure what the charge time is. But makes sure...

Not sure what the charge time is. But makes sure it is plugged in fully and let it go until it stops.
03-07-2023, 08:06 PM
Replies: 6
Views: 267
Posted By FUTABA-RC

Some cards just do not play nice. I use sandisk...

Some cards just do not play nice. I use sandisk cards. You do not want or need super high speed cards.
03-01-2023, 10:57 PM
Replies: 26
Views: 1,614
Posted By FUTABA-RC

Given how few exemptions there are I would not be...

Given how few exemptions there are I would not be overly concerned by that. And given that those that do exist were only granted after intensive process involving the FAA I am also not concerned...
03-01-2023, 01:30 PM
Replies: 26
Views: 1,614
Posted By FUTABA-RC

So 393.7 feet to 492.1 feet. Seems 400 feet is...

So 393.7 feet to 492.1 feet. Seems 400 feet is towards the low end of what other countries do.
02-19-2023, 06:49 PM
Replies: 3
Views: 631
Posted By FUTABA-RC

True and True

True and True
02-19-2023, 06:48 PM
Replies: 1
Views: 262
Posted By FUTABA-RC

What receiver are you speaking about?

What receiver are you speaking about?
02-03-2023, 09:12 AM
Replies: 1
Views: 233
Posted By FUTABA-RC

Registration is done mostly if the TX fails to...

Registration is done mostly if the TX fails to recognize the sensor or if you need to assign it to a particular slot group. Using more than one of the same sensor also requires registration in the TX.
Replies: 19
Views: 1,650
Posted By FUTABA-RC

Futaba is always very tight-lipped about new...

Futaba is always very tight-lipped about new products. I have not heard anything. They did just announce a refresh of the 16IZ, but no idea when it will be available. Nothing earth shattering in the...
01-30-2023, 09:07 PM
Replies: 1
Views: 286
Posted By FUTABA-RC

A couple of different ways to do it. You could...

A couple of different ways to do it. You could simply set a dual rate with a zero throttle curve.

I use conditions with the default condition having a zero throttle.
01-29-2023, 07:37 PM
Replies: 1
Views: 347
Posted By FUTABA-RC

Futaba does not publish (and I have never seen)...

Futaba does not publish (and I have never seen) any max temperature figures. Sounds like it is working fine, so I'd suggest simply trying to keep it cool between runs. Don't let it sit in direct sun,...
Replies: 19
Views: 1,650
Posted By FUTABA-RC

If you are in the US then all the current Futaba...

If you are in the US then all the current Futaba radios will work with ALL Futaba protocols. In the EU only the 16IZ does not work with FASST, all others do.
01-24-2023, 11:31 PM
Replies: 3
Views: 1,071
Posted By FUTABA-RC

Good info. Thanks for sharing!!

Good info. Thanks for sharing!!
01-18-2023, 07:04 PM
Replies: 1
Views: 322
Posted By FUTABA-RC

Futaba designed these servos with maximum...

Futaba designed these servos with maximum performance in mind. Honestly in the rare instances that I have had a similar situation (hunting around center) all I did was increase the deadband a bit...
01-13-2023, 10:59 PM
Replies: 5
Views: 703
Posted By FUTABA-RC

Good info in the posts above. Quick reminder this...

Good info in the posts above. Quick reminder this is the vendor support forum and not the open discussion forum.
01-04-2023, 04:20 PM
Replies: 24
Views: 733
Posted By FUTABA-RC

Honestly since this happens with multiple...

Honestly since this happens with multiple transmitters, different receivers and different servos I am at a total loss. Have you tried a whole new model with no programming in it other than channel...
12-25-2022, 09:36 AM
Replies: 1
Views: 284
Posted By FUTABA-RC

Make sure the transmitter is in 14-channel...

Make sure the transmitter is in 14-channel FASSTest and not 12-channel FASSTest

If you are not using telemetry you can try setting the RX abd TZ to FASST instead of FASSTest as well.
12-20-2022, 12:23 PM
Replies: 24
Views: 733
Posted By FUTABA-RC

So wait, using a completely different transmitter...

So wait, using a completely different transmitter you have the same issue?
12-20-2022, 12:22 PM
Replies: 3
Views: 485
Posted By FUTABA-RC

Go into the servo reverse menu. Reverse the...

Go into the servo reverse menu. Reverse the throttle channel
12-12-2022, 08:13 PM
Replies: 10
Views: 994
Posted By FUTABA-RC

Sorry for your troubles. Wish I could be more...

Sorry for your troubles. Wish I could be more help.
12-10-2022, 08:14 PM
Replies: 24
Views: 733
Posted By FUTABA-RC

You are in the USA. You can contact FutabaUSA to...

You are in the USA. You can contact FutabaUSA to see if they still service that radio. Or try RadioSouth.
12-10-2022, 08:13 PM
Replies: 10
Views: 994
Posted By FUTABA-RC

Create a simple model. Do not do any mixing, etc....

Create a simple model. Do not do any mixing, etc. That will tell you if some condition you are not tracking in the other model is the issue
Showing results 1 to 25 of 500
 


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service - Do Not Sell or Share My Personal Information -

Copyright © 2023 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.