RCU Forums - Search Results

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Notices
Search: Posts Made By: speedracerntrixie
Showing results 1 to 10 of 10
Search took 0.01 seconds.
08-31-2018, 10:33 AM
Replies: 25
Views: 6,037
Posted By speedracerntrixie

Hans, I wish I had a solution for you. This is my...

Hans, I wish I had a solution for you. This is my second Dualsky F3A motor and both have always run flawlessly. I am using the OS controller on both with the settings of 20 degrees timing, 14 poles...
08-30-2018, 10:25 AM
Replies: 25
Views: 6,037
Posted By speedracerntrixie

https://cimg9.ibsrv.net/gimg/www.rcuniverse.com-vb...

https://cimg9.ibsrv.net/gimg/www.rcuniverse.com-vbulletin/1024x683/8dc93fc9_545b_49e2_8a22_c3881a5ca44d_483c4054f4240a5aa67a2dc4b0a432835a9a33fa.jpeg...
05-10-2018, 04:49 PM
Replies: 25
Views: 6,037
Posted By speedracerntrixie

https://cimg8.ibsrv.net/gimg/www.rcuniverse.com-vb...

https://cimg8.ibsrv.net/gimg/www.rcuniverse.com-vbulletin/2000x2000/img_4186_03604d690ff15c11bf845aafa9352aa244c9d703.jpg
I would add a rear support much like the one here.
05-10-2018, 03:36 PM
Replies: 25
Views: 6,037
Posted By speedracerntrixie

https://cimg6.ibsrv.net/gimg/www.rcuniverse.com-vb...

https://cimg6.ibsrv.net/gimg/www.rcuniverse.com-vbulletin/2000x1493/img_4185_36649e352d45e508490dcb07c881433440d824eb.jpg
I would suggest the Dualsky mount. I used one in my Hydeaway that previously...
05-09-2018, 02:25 PM
Replies: 25
Views: 6,037
Posted By speedracerntrixie

I agree, those instructions suck. I would suggest...

I agree, those instructions suck. I would suggest however to run a minimum of 20 degrees on a 63mm outrunner.
05-09-2018, 08:16 AM
Replies: 25
Views: 6,037
Posted By speedracerntrixie

My apologies but I am only going on the...

My apologies but I am only going on the information that you are providing. Your timing setting is one thing that is concerning to me. The description that you give leads me to believe that you are...
05-08-2018, 03:55 AM
Replies: 25
Views: 6,037
Posted By speedracerntrixie

I would highly suggest that while waiting for...

I would highly suggest that while waiting for your new motor you learn about them. I do not think that the issues you are having are the fault of the motors. I could be wrong but the information or...
04-25-2018, 08:18 AM
Replies: 25
Views: 6,037
Posted By speedracerntrixie

I agree that they would be answering emails more...

I agree that they would be answering emails more quickly. However do not know where your timing is set. This is important as having the timing too far off will cause the motor to run hot as will not...
04-24-2018, 03:59 AM
Replies: 25
Views: 6,037
Posted By speedracerntrixie

The 20x13 three blade prop is too much for a 220...

The 20x13 three blade prop is too much for a 220 KV motor. I'm not familiar with that speed control and have no idea what factory settings are but for a large outrunner the timing should be around...
04-16-2018, 05:17 PM
Replies: 25
Views: 6,037
Posted By speedracerntrixie

I am at a loss of what to tell you. I agree that...

I am at a loss of what to tell you. I agree that they should be talking with you to solve your issue. I however without getting more information about your setup will not make any assumptions that...
Showing results 1 to 10 of 10


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service - Do Not Sell My Personal Information

Copyright 2018 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.