Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Notices
 
Search: Posts Made By: TJ Moran
Showing results 1 to 25 of 45
Search took 0.73 seconds.
12-08-2013, 03:26 PM
Replies: 8
Views: 617
Posted By TJ Moran

YS FZ115 Sport quits in flight after 2-3 flights

Title says it.
YS 20/20 fuel.
OS type F Plug
16 X 6 APC sport prop
Engine mounted with cylinder sideways.

This is happening in 2 different airframes. Both planes this is happening with have...
08-08-2012, 02:38 PM
Replies: 7
Views: 977
Posted By TJ Moran

RC Flying Site Issues Due To Li-Po Fires

An RC flying site in my area has been closed to all aircraft due to a aircraft crash and subsequent fire caused by a badly damaged lithium polymer battery. Iā€™m trying to collect data and...
05-23-2009, 08:03 PM
Replies: 21
Views: 1,333
Posted By TJ Moran

RE: project

Hey, why not revert back to WW II and do like the krauts. Build a little 3-wheeled dolly with a cheapo receiver and tiny nicad and a small steering servo for a single nosewheel. Hit the throttle,...
Forum: Gas Engines
01-03-2009, 08:55 PM
Replies: 4
Views: 724
Posted By TJ Moran

RE: TME Smoke Pump Seals

Thanks, Mr. Bigg

I will look into the JCW pump

TJ Moran
Forum: Gas Engines
01-03-2009, 05:52 PM
Replies: 4
Views: 724
Posted By TJ Moran

TME Smoke Pump Seals

Flying a 3W Extra 330 with a DA 150.

I have 2 TME smoke pumps Part Number SSP-IIB With leaky motor shaft seals. I disassembled one pump and replaced the o-ring (available from hardware store)...
Forum: Gas Engines
01-07-2007, 09:05 PM
Replies: 7
Views: 1,829
Posted By TJ Moran

RE: Biela props??

Let's keep this thread going ! It could become another U-Can-Do-3D 46 !
I've used a Biela 22-6 on a ZDZ40 in a UCD 120. Great prop - pulls well and really pretty (like a supermodel). Tried a...
Forum: ARF or RTF
12-31-2006, 03:07 PM
Replies: 1,010
Views: 103,043
Posted By TJ Moran

RE: Hangar 9 Funtana 40

After about 50 logged flights and reading this thread several times, I finally "bit the bullet" and cut back the leading edge covering, shaved off all but about 1/16 inch of the leading edges, and...
12-30-2006, 02:06 PM
Replies: 13
Views: 1,694
Posted By TJ Moran

RE: Microjet set up please help....

I fly the Microjet with a Mega 16-15-2 (4600Kv) spinning an APC 4.75 X 4.75 prop; Jeti 70 amp BEC speed controller, with an EVO 2100 Mah 3S 1P 20C/30C burst pack. P-calc figures (Diversity Models...
12-30-2006, 02:03 PM
Replies: 3
Views: 899
Posted By TJ Moran

RE: Brushless upgrade for Multiplex Micro-Jet

I fly the Microjet with a Mega 16-15-2 (4600Kv) spinning an APC 4.75 X 4.75 prop; Jeti 70 amp BEC speed controller, with an EVO 2100 Mah 3S 1P 20C/30C burst pack. P-calc figures (Diversity Models...
12-30-2006, 01:56 PM
Replies: 16
Views: 3,279
Posted By TJ Moran

RE: hobby lobby micro jet

I fly the Microjet with a Mega 16-15-2 (4600Kv) spinning an APC 4.75 X 4.75 prop; Jeti 70 amp BEC speed controller, with an EVO 2100 Mah 3S 1P 20C/30C burst pack. P-calc figures (Diversity Models...
Forum: 3D Flying!
11-29-2006, 09:12 PM
Replies: 130
Views: 20,967
Posted By TJ Moran

RE: Fliton Inspire 60 Acro

CafeenMan
One possible solution not mentioned in this thread to help a vicious snap problem is to seal the aileron gaps completely with covering or tape. I had an ARF I got already-built from...
Forum: Gas Engines
10-16-2006, 11:18 PM
Replies: 1
Views: 819
Posted By TJ Moran

RE: AIR MODELS PROPS

Air Models 32-11 works great for 3D on a DA 150 in a 37.5 pound 3W Patty Wagstaff Extra 330.
It will rip if you let it over rev.
I like the prop.

DA sells them.

TJ
Forum: Gas Engines
10-16-2006, 11:12 PM
Replies: 3
Views: 884
Posted By TJ Moran

RE: Wood 22 X 6 Prop

These guys in Canada have Birch 22-6 props.

http://www.clarkindustries.on.ca/


I bought a couple of 24-6 props for a ZDZ 40 RV. It ran great with them.

TJ
Forum: 3D Flying!
09-16-2006, 07:33 PM
Replies: 14
Views: 1,034
Posted By TJ Moran

RE: thrust and weight???

Don't forget Coreolis effect. It can be a killer.

TJ
Forum: 3D Flying!
09-09-2006, 10:05 PM
Replies: 4
Views: 567
Posted By TJ Moran

RE: 150 prop

Got a DA 150 in a 40% 3W extra 330.
Weighs 37.5 pounds dry. Flying at about 650 feet above sea level.
Prop is Air Models 32-11 sold by DA
The prop has great acceleration, good pull in the...
Forum: 3D Flying!
09-09-2006, 07:53 PM
Replies: 27
Views: 1,835
Posted By TJ Moran

RE: FUNTANA 40

Mine has a YS 110 FZ in it. I just LOVE that engine!
Still sorting out throws, DRs, Expos, and mixing.

TJ
Forum: 3D Flying!
09-02-2006, 09:34 PM
Replies: 53
Views: 4,005
Posted By TJ Moran

RE: What Power are you Funtana Flyers using?

YS 110 FZ. Anything smaller makes a good fishing weight.
Size matters.
"It has way too much power, which is almost enough."


tj
Forum: 3D Flying!
09-01-2006, 08:35 PM
Replies: 53
Views: 4,005
Posted By TJ Moran

RE: What Power are you Funtana Flyers using?

I put a YS 110 FZ in My FuntanaS40.

TJ

"It has way too much power - -which is almost enough."
Forum: 3D Flying!
06-25-2006, 05:13 AM
Replies: 4
Views: 659
Posted By TJ Moran

RE: YS 110 3D setup?

I agree with Raideron. I am currently using an APC 16.5 X 5W on my YS 110 FZ and both it and the 17 X 4W seem to rev and pull equally well. As Raideron said you gotta watch the wide open throttle...
Forum: 3D Flying!
06-24-2006, 08:16 PM
Replies: 41
Views: 2,719
Posted By TJ Moran

RE: Which engine for a Funtana S from Hangar 9

Just got the box with the FuntanaS 40 a couple of days ago. Once again I am amazed at what you can buy in the ARFs today. Hangar 9 seems to do a great job, along with all the rest. Mines gonna get a...
Forum: Gas Engines
10-16-2005, 07:47 PM
Replies: 4
Views: 1,511
Posted By TJ Moran

RE: DA-150 Carburator P/N

I think the DA-150 basic Walbro Carb is the WB series. This series carb is also used on the ZDZ 210. Different carb numbers after the WB identifier have to do with various choke bores, venturi bores,...
Forum: Gas Engines
07-26-2005, 08:54 PM
Replies: 10
Views: 821
Posted By TJ Moran

RE: Least width 100cc twin?

One other thing to consider is putting about 2.5 to 3 degrees of right thrust on the engine. This pretty much the standard depending on a whole buncha variables. If you keep the prop hub in the...
Forum: Gas Engines
03-13-2005, 07:24 PM
Replies: 6
Views: 2,945
Posted By TJ Moran

RE: Tuned Pipe Coupler Material

I have been successfully using a High Temp Exhaust Coupling sold by Octura Model Marine Supplies for connecting tuned pipes to headers on 2-strokes. It doesn't last forever, but it outlasts anything...
Forum: Gas Engines
03-09-2005, 09:18 PM
Replies: 23
Views: 3,765
Posted By TJ Moran

RE: engine for ultra stick lite 120

A homemade 2 into 1 aluminum canister muffler going into a fitting over the wing which Ys into 2 3/4 inch aluminum tubes running out through the lightning holes in the ribs forward of the spar. A...
Forum: Gas Engines
03-08-2005, 11:22 PM
Replies: 23
Views: 3,765
Posted By TJ Moran

RE: engine for ultra stick lite 120

I've got an old Ultra Stick 120 (not the lite version) with a Brison 108 CC on it.
Seems to have adequate power.
Flys great!!
Has smoke out the wingtips.

TJ
Showing results 1 to 25 of 45
 


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service - Do Not Sell My Personal Information -

Copyright © 2018 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.