Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Notices
 
Search: Posts Made By: huck1199
Showing results 1 to 25 of 500
Search took 0.64 seconds.
07-25-2013, 04:23 PM
Replies: 1
Views: 321
Posted By huck1199

RE: rigger question

A lot of guys use hockey stick tape
Forum: Glow Engines
07-17-2013, 10:29 PM
Replies: 20
Views: 1,695
Posted By huck1199

RE: mecoa

I have ordered parts in the past with no problem; but that was 2 years ago.
07-09-2013, 12:50 PM
Replies: 5
Views: 471
Posted By huck1199

RE: Cameras

If your plane is gas or glow the vibration is an issue with picture quality.
06-10-2013, 01:42 PM
Replies: 23
Views: 1,519
Posted By huck1199

06-10-2013, 01:11 PM
Replies: 23
Views: 1,519
Posted By huck1199

RE: Do transmitters go bad?

I would suspect the connections on the module - 12 yrs is a long time.
06-10-2013, 12:46 PM
Replies: 23
Views: 1,519
Posted By huck1199

RE: Do transmitters go bad?

Does the radio work with 72mhz rx's without the module?
06-10-2013, 12:37 PM
Replies: 29
Views: 2,017
Posted By huck1199

RE: Why Are People Mad

Close minded people think that what they do is the only way to do something.
06-10-2013, 12:34 PM
Replies: 2
Views: 326
Posted By huck1199

RE: power starter

Counter clockwise
06-07-2013, 09:01 PM
Replies: 14
Views: 815
Posted By huck1199

RE: Charging weirdness

It is not that far out of balance - just balance it.
Forum: Glow Engines
06-05-2013, 04:00 PM
Replies: 5
Views: 901
Posted By huck1199

RE: Magnum 70 XL

My 80 ran great from the start. No longer made.
05-10-2013, 12:45 PM
Replies: 6
Views: 691
Posted By huck1199

RE: Fire Engine compartment

Was the engine hot from a previous run?  Is a fuel line leak possibly at fault?
Forum: Gas Engines
05-02-2013, 12:57 PM
Replies: 15
Views: 2,602
Posted By huck1199

RE: Ideas to quiet a beast motor

I have a 52 cm that is loud - I was going to try to stuff it with stainless steel scrubbing pad. Don't know if it will work - just an idea now.
Forum: Glow Engines
04-29-2013, 09:45 PM
Replies: 25
Views: 2,118
Posted By huck1199

RE: K&B Sportster 65

Are you sure it is a .65? There is an .82 ducted fan with rear exhaust. See this link http://www.mecoa.com/kb/aero/ductedfan.htm
Forum: Gas Engines
04-21-2013, 01:46 PM
Replies: 36
Views: 2,545
Posted By huck1199

RE: Gas engine starts and splutters out

Could it be that the ignition won't work at normal rpm ranges?
Forum: Kit Building
04-13-2013, 01:04 PM
Replies: 27
Views: 7,169
Posted By huck1199

RE: Canopy/ windshield adhesive.

When using RC-56 you have to make sure the fit is air tight so air flow cannot lift the part.
Forum: Kit Building
04-07-2013, 05:21 PM
Replies: 42
Views: 8,067
Posted By huck1199

RE: foam wing adhesive

<span style="font-family: Verdana, Arial; font-size: 13px; background-color: rgb(251, 252, 255);">3M 77 spray contact cement can disolve some foams; so test first.</span>
04-07-2013, 05:19 PM
Replies: 5
Views: 488
Posted By huck1199

RE: A newbie frequency question....

One of you would have to change to a different transmitter and receiver on a different channel. Hardly seems worth that expense for such low cost boats.
Forum: Kit Building
04-05-2013, 03:38 PM
Replies: 12
Views: 771
Posted By huck1199

RE: Id of original Lazer 200 kit maker

I have a Lanier 1/4 laser 200 kit. It has a foam wing that need to be sheeted with balsa.  Sounds like my kit.
03-25-2013, 10:29 AM
Replies: 5
Views: 632
Posted By huck1199

RE: Need some Dope tips

If you use fabric store cloth make sure it is 100% polyester and not pre-shrunk.
Forum: Gas Engines
03-14-2013, 04:49 PM
Replies: 24
Views: 2,029
Posted By huck1199

RE: Carb spitting out fuel

Is the condition such that a reed that is not seated will allow fuel to reguritate?
Forum: Gas Engines
03-08-2013, 02:15 PM
Replies: 2
Views: 482
Posted By huck1199

RE: FUEL LINE MATERIALS

Tefzel looks like a winner. Although expensive ($17.50 for 5 ft tube - 1/8") it might be a smart matterial for use inside tanks and other places where replacement is difficult.
Forum: Kit Building
03-03-2013, 02:58 PM
Replies: 24
Views: 1,401
Posted By huck1199

RE: Build threads, just an idea........

An easier to implement fix would be to tag photos with the post numbers. You could use the gallery option to find the photo that covers the build stage you want, then click to the post.
Forum: Kit Building
02-22-2013, 01:38 PM
Replies: 12
Views: 3,176
Posted By huck1199

RE: Cutting hinge slots with Aero Broach ?

I have a set of old Dubro two-pronged forks that work OK but don't really remove much material. I also have a slot machine that I find almost useless.  The broach looks like it would work better than...
Forum: Kit Building
02-07-2013, 05:12 PM
Replies: 17
Views: 1,273
Posted By huck1199

RE: Sealing Monocote Edges

Water based polyacrylic
Forum: Kit Building
02-07-2013, 05:04 PM
Replies: 17
Views: 1,273
Posted By huck1199

RE: Sealing Monocote Edges

I use a little wbp brushed on with a small brush.  Not really fuel proof; but I clean my planes after each flight.
Showing results 1 to 25 of 500
 


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service - Do Not Sell My Personal Information -

Copyright 2021 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.