RCU Forums - Search Results

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Notices
Search: Posts Made By: [email protected]
Showing results 1 to 12 of 12
Search took 0.01 seconds.
08-16-2022, 07:33 AM
Replies: 0
Views: 307
Posted By [email protected]

Kingtech K45G2 spool up temps

Hi there

Need some advice pls. I have a kingtech k45 that Iím a little concerned about.

on the factory settings (column 1) my turbine starts up fine but noticed the temps on startup are pretty...
Forum: RC Jets
01-29-2021, 05:22 AM
Replies: 0
Views: 895
Posted By [email protected]

HELP: JetLegend F-18 1:7.5

HI Guys. Attached pics of my jet. I was hoping someone could assist with the following questions:-

Is this the jetlegend F-18 1:7.5 Airframe? or some other brand. I have attached pics for...
Forum: RC Jets
01-27-2021, 09:54 AM
Replies: 37
Views: 13,484
Posted By [email protected]

hi there thanks for getting back to me. My...

hi there

thanks for getting back to me. My jet has two carbon spars in the wing. Definitely no single aluminum tube. So this is definitely the jet legend airframe?

thanks for letting me know...
Forum: RC Jets
01-24-2021, 02:09 PM
Replies: 37
Views: 13,484
Posted By [email protected]

CG

Hi guys. I got the jet legend f18 1/8th as per all the pics Iím seeing on this thread (bought second hand)

got no manual online and was wondering if someone could advise where the best CG is on...
12-13-2020, 11:36 AM
Replies: 2
Views: 1,645
Posted By [email protected]

When supersport spoil up help

Hi everyone. Need a little advice. I have a wren supersport on my boomerang sprint. Iím new to turbines.

The engine starts up and runs fine. Gets to idle and the moving my throttle stick to check...
Forum: RC Jets
11-26-2020, 09:17 PM
Replies: 15
Views: 2,195
Posted By [email protected]

hi, Iím sing servos that have 20kg-cm. That...

hi, Iím sing servos that have 20kg-cm. That should be ok?
Forum: RC Jets
11-26-2020, 08:58 PM
Replies: 15
Views: 2,195
Posted By [email protected]

Thanks

Thanks everyone! Exactly what I wanted to hear.. years of experience counts and glad to know guys using the savox say they extremely reliable.

so far I have had many jet guys saying people are...
Forum: RC Jets
11-26-2020, 09:11 AM
Replies: 15
Views: 2,195
Posted By [email protected]

hi, yes, I know. Would like to move towards HV...

hi, yes, I know. Would like to move towards HV servos but I know guys have been flying turbine jets on 6v setups for centuries.. most of my colleagues are so used to using older servos that the...
Forum: RC Jets
11-26-2020, 08:49 AM
Replies: 15
Views: 2,195
Posted By [email protected]

Servos for my jet. Confused

Hi guys

I bought an f18 1/8 scale turbine jet. Itís the jet legend f18 or BVM F18 1/8th scale.

the model currently has JR DS171 servos on the ailerons and rudders. I was told these are more...
Forum: RC Jets
11-10-2020, 12:42 AM
Replies: 13
Views: 1,242
Posted By [email protected]

Thanks everyone, removing all the servo reversers...

Thanks everyone, removing all the servo reversers from this jet and will install a powerbox professional to do the mixing. I just found out this is the ultimate solution for my high voltage servos...
Forum: RC Jets
11-09-2020, 01:53 PM
Replies: 13
Views: 1,242
Posted By [email protected]

With

Thanks for the responses.

my dilemma: I fly lots of 3D helis and moved all of them over to vbar neos. This system is amazing, donít need a separate gyro either as itís built in

i can do all my...
Forum: RC Jets
11-09-2020, 12:48 PM
Replies: 13
Views: 1,242
Posted By [email protected]

Servo reversers

Hi there

I am getting into turbine jets and Iíve never used servo reversers in any of my models in the past. My receivers have 9 Channels and can get my two jets working on this but with about 3...
Showing results 1 to 12 of 12


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service - Do Not Sell My Personal Information -

Copyright © 2022 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.