RCU Forums - Search Results

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Notices
Search: Posts Made By: Turbotronic
Showing results 1 to 14 of 14
Search took 0.01 seconds.
Forum: RC Jets
01-06-2022, 12:13 AM
Replies: 111
Views: 6,825
Posted By Turbotronic

Awesome! I have some 3mm soft copper tubing, just...

Awesome! I have some 3mm soft copper tubing, just need a bigger torroid to complete...
Forum: RC Jets
01-02-2022, 09:07 AM
Replies: 111
Views: 6,825
Posted By Turbotronic

Thumbs up That is good to know! Will have to try myself.

That is good to know! Will have to try myself.
Forum: RC Jets
12-14-2021, 01:12 AM
Replies: 111
Views: 6,825
Posted By Turbotronic

https://www.youtube.com/watch?v=jLRgDZeYQ-M ...

https://www.youtube.com/watch?v=jLRgDZeYQ-M
Thanx, a good find! Going to try this for sure.
Forum: RC Jets
12-13-2021, 09:04 AM
Replies: 111
Views: 6,825
Posted By Turbotronic

Could not get it to heat large pieces of brass...

Could not get it to heat large pieces of brass either. The heat absorbed is related directly to current draw when something is placed within coil. Hardly changes with brass tube and tube not even...
Forum: RC Jets
12-13-2021, 08:06 AM
Replies: 111
Views: 6,825
Posted By Turbotronic

I have that exact same unit, used it with 9s...

I have that exact same unit, used it with 9s life. I eagerly await positive feedback on your efforts!
Forum: RC Jets
12-12-2021, 11:59 PM
Replies: 111
Views: 6,825
Posted By Turbotronic

Never tried brass but with SS needles I would say...

Never tried brass but with SS needles I would say use the thicker wall types, it will make any bending easier. Using some sort of shield to keep direct flame away from needle could help. If you get...
Forum: RC Jets
12-12-2021, 08:50 AM
Replies: 111
Views: 6,825
Posted By Turbotronic

When using even 56% solder paste you can use a...

When using even 56% solder paste you can use a regular gas torch as plumbers do when soldering copper pipes. Brass melts at a lot lower temp than copper so the solder melt temp is obviously critical....
Forum: RC Jets
11-24-2021, 11:03 PM
Replies: 111
Views: 6,825
Posted By Turbotronic

Some 23 years ago I tested Brass caged GMN...

Some 23 years ago I tested Brass caged GMN bearings provided as a sample. Those had the white ceramic (Alu oxide) balls. At the time balancing was an issue for me and they broke at about 150KRPM....
Forum: RC Jets
11-22-2021, 11:03 PM
Replies: 111
Views: 6,825
Posted By Turbotronic

Yes this is correct, and is one of the downsides...

Yes this is correct, and is one of the downsides of using full compliment bearings. It get a lot worse after an engine run where the engine is not cooled down. It can then lock up quite solidly, to...
Forum: RC Jets
11-06-2021, 02:45 AM
Replies: 111
Views: 6,825
Posted By Turbotronic

No question they will work, GRW is used in...

No question they will work, GRW is used in majority of turbines on the market. The rear only preload of the KJ is not a good idea. You need to preload the front and not have it restricted in movement...
Forum: RC Jets
11-06-2021, 01:57 AM
Replies: 111
Views: 6,825
Posted By Turbotronic

Almost all non-standard configuration bearings...

Almost all non-standard configuration bearings from all manufacturers are subject to MOQ's. I can tel you that GRW also makes similar bearings for a MOQ. The ones we buy for "model use" have never in...
Forum: RC Jets
11-02-2021, 01:27 AM
Replies: 111
Views: 6,825
Posted By Turbotronic

Ceramic Silicon Nitride

Ceramic Silicon Nitride
Forum: RC Jets
10-31-2021, 01:32 AM
Replies: 111
Views: 6,825
Posted By Turbotronic

A few actual facts: Full compliment is not the...

A few actual facts:
Full compliment is not the best option in high rpm applications. We get away with it due to reduced life expectancy.
AMT uses angular contact bearings with machined brass cages....
Forum: RC Jets
10-28-2021, 08:21 AM
Replies: 111
Views: 6,825
Posted By Turbotronic

I share that notion. In small turbines the rear...

I share that notion. In small turbines the rear bearing takes near all the axial load. Bad because it really hot already, good because the overhang and turbine mass do not need as much radial...
Showing results 1 to 14 of 14


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service - Do Not Sell My Personal Information -

Copyright 2021 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.