Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Notices
 
Search: Posts Made By: griesel
Showing results 1 to 25 of 136
Search took 0.48 seconds.
Replies: 0
Views: 476
Posted By griesel

copying Aurora 9x to Aurora 9X

Can this be done? I bought a 2nd A9x as a backup and finally hooked up to copy A9x to A9x. The HPP-22 software says A9x transmitter is not available. Are there plans to make this feature available?
02-03-2014, 02:52 AM
Replies: 8
Views: 4,869
Posted By griesel

I would agree if it is freewing. Dynam stuff is...

I would agree if it is freewing. Dynam stuff is pretty good. A lot of guys fly the heck out of them at my club and most of them last until a major pilot error.
I have a Carbon Z Yak 54 that is...
Replies: 171
Views: 109,570
Posted By griesel

Aurora 9X, printing manual, Walkera QR X350 quad copter

1. I have a new Aurora 9X and was a little disgruntled when I discovered no hard copy manual. I printed out in booklet form on an HP Office Jet 8600+ which ended up as 32 pages. I then...
Forum: Aerodynamics
08-21-2013, 11:45 AM
Replies: 29
Views: 3,422
Posted By griesel

It goes by weight. Twice the scale, with...

It goes by weight. Twice the scale, with everything else equal (it seldom is ) the weight would go up 8 times which would require 8 times the
horsepower. This will get you in the right ballpark.
Forum: 3D Flying!
03-23-2013, 06:17 PM
Replies: 1,674
Views: 207,924
Posted By griesel

RE: Great Planes Reactor GP/EP 3D ARF .46-.70

I have an electric reactor with 251 flights on it so far. I use it to practice IMAC Basic. Power is Turnigy L5055C motor ( 1600 watts max), Turnigy Plush 80 amp ESC,
Turnigy 4.0 AH 30C 6S battery...
02-07-2013, 12:46 PM
Replies: 1
Views: 884
Posted By griesel

RE: ParkZone Albatros build and fly

<span style="font-size: larger;">I tried 2650mah 40C batteries and they were difficult to load. Am going back to the 2250mah 40C. Found some weak spots in the Albatros The wheel plates break
at the...
02-04-2013, 02:40 PM
Replies: 1
Views: 884
Posted By griesel

ParkZone Albatros build and fly

<span style="font-size: larger;"><span style="font-family: Arial;">It went together in about 8 hours and I am slow. It was pretty easy except for where the plastic keepers go where the landing gear...
04-14-2012, 05:46 AM
Replies: 8
Views: 4,869
Posted By griesel

RE: Freewing mosquito build

<span style="font-size: larger;">It crashed - demolished. At 40% throttle with the wheels down, and a sharp left aileron turn, it snapped and went into the ground before recovery.
When checking out...
04-06-2012, 04:14 PM
Replies: 8
Views: 4,869
Posted By griesel

RE: Freewing mosquito build

<span style="font-size: larger;">Finished it today. Weight with Turnigy Ntech 2.2AH 4S 35C 4.6 lbs. About a half a pound more than book weight.
CG with battery all the way forward and retracts down...
03-17-2012, 11:38 AM
Replies: 8
Views: 4,869
Posted By griesel

RE: Freewing mosquito build

<span style="font-size: larger; ">Mosquito door delay circuit:
With the cable laid out with white to right; single in bottom;
double out top( this is the double row of pins )
landing gear is...
03-16-2012, 08:16 AM
Replies: 8
Views: 4,869
Posted By griesel

Freewing mosquito build

Problem 1. The wheel doors were painted before the plastic hinges and horn were glued on.
The glue sticks the paint to the plastic but the paint does not stick very well to the foam. The
plastic...
Forum: Gas Engines
12-16-2011, 05:07 PM
Replies: 8
Views: 1,043
Posted By griesel

RE: Dubros round nose tank has less useable fuel

Yes if I had landed with the throttle off or nearly off. But I went to 1/2 throttle and used
up the fuel in the line in about 3 seconds.
Forum: Gas Engines
12-16-2011, 11:47 AM
Forum: Gas Engines
12-16-2011, 06:54 AM
Replies: 8
Views: 1,043
Posted By griesel

Dubros round nose tank has less useable fuel

<span style="font-size: larger; ">I had a Hempel Yak 55M 50CC with a Dubros 424 round nose 24 ounce tank
in it.I was landing with a slight nose down attitude; about 500 ft. of down wind;
400ft of...
10-14-2011, 09:22 AM
Replies: 32
Views: 9,284
Posted By griesel

RE: Great Planes Yak-55M Sport/3D ARF 50-55cc,88

I have bought, assembled, and flown the Great Planes Yak 55M 50CC. I paid $475 to Hobby Warehouse delivered. I used a coupon discount. It arrived
promptly in good condition. The box was labeled...
04-13-2011, 07:03 PM
Replies: 23
Views: 10,622
Posted By griesel

RE: E-flite carbon z yak 54 build and fly

They only come PNP; Plug and PLAY or
BNF Bind and Fly. Both of which include
the motor and ESC. Check Horizon.com
For what comes with each version and
what is needed to fly one. It is a very well...
Forum: Kit Building
03-16-2011, 03:58 PM
Replies: 1,183
Views: 134,863
Posted By griesel

RE: Tower Hobbies Uproar 40 build

I have bought a couple of uproar 40's arf's from Tower. I am going to put them together as electrics. I have flown a bunch of 4lb
electrics andhave arrived at what I think are good servo's. Hitec HS...
Forum: Glow Engines
01-25-2011, 07:13 PM
Replies: 166
Views: 45,824
Posted By griesel

RE: O.S. 95 AX !!!

After I got them running and tuned the os 95AX did not dead stik.
What they did do was run poorly at 50% throttle. This got worse
with colder weather. Going to 20% nitro and changing the glo
plug...
12-29-2010, 02:50 PM
Replies: 23
Views: 10,622
Posted By griesel

RE: E-flite carbon z yak 54 build and fly

Broke the 2nd motor mount. The metal is very brittle. If I contacted Horizon they would probably
send me another brittle one. Decided to make one. Using a drill press, several metal saws,
and an...
12-29-2010, 02:45 PM
Replies: 23
Views: 10,622
Posted By griesel

RE: E-flite carbon z yak 54 build and fly

Here are some actual weights of parts:motor 199.7 grams;adapter and prop nut 18.0 grams;
spinner and bolt 6.3 grams;12X5.25 prop 22.8 grams; pilot and his glue 25.3 grams
The problem with the motor...
12-21-2010, 09:19 AM
Replies: 23
Views: 10,622
Posted By griesel

RE: E-flite carbon z yak 54 build and fly

4th day in warm Arizona. I heard a buzzing noise at low prop rpm yesterday and again this morning.
The prop was not loose and the spinner was ok. Found some motor mounting screws loose and ...
12-20-2010, 04:17 PM
Replies: 23
Views: 10,622
Posted By griesel

RE: E-flite carbon z yak 54 build and fly

3rd day in warm Arizona. 5 flights. Tried hi rates today. OMG Insane. the roll rate was approx 1500 degrees/sec ( too fast to count ).
And too fast to come out in any known position. Elevator: it...
12-19-2010, 04:45 PM
Replies: 23
Views: 10,622
Posted By griesel

RE: E-flite carbon z yak 54 build and fly

Static thrust test plane w/battery weight = 59.25 ounces.
Battery 2.2ah 40C 4S Turnigy 60amp 92 ounces approx 960 watts thrust to weight 1.6
Battery 2.2ah 35C 4S Turnigy nanotech ...
12-19-2010, 09:42 AM
Replies: 23
Views: 10,622
Posted By griesel

RE: E-flite carbon z yak 54 build and fly

2nd day, 3 flights.   Overlaying the velcro ends does not work.  The battery slides toward the tail.<div>Back to the original  of putting the small end thru the hole and looping back and down....
12-18-2010, 09:20 PM
Replies: 23
Views: 10,622
Posted By griesel

E-flite carbon z yak 54 build and fly

Disclaimer: All the problems found so far I consider minor. This is the PNP version.
The plane was purchased for IMAC Basic practice so there will not be 3D flight information.
The part of the...
Showing results 1 to 25 of 136
 


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service - Do Not Sell My Personal Information -

Copyright 2018 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.