RCU Forums - Search Results

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Notices
Search: Posts Made By: john.j.allen
Showing results 1 to 9 of 9
Search took 0.21 seconds.
Forum: ARF or RTF
10-01-2017, 05:26 AM
Replies: 8
Views: 3,217
Posted By john.j.allen

I've finally got my MXS-R back in the air (still...

I've finally got my MXS-R back in the air (still tuning the DLE30), but as I feed in up elevator once I reach a certain point the model rolls hard left. Anybody else experience this?
Forum: Gas Engines
05-22-2017, 06:20 AM
Replies: 23
Views: 7,361
Posted By john.j.allen

The bolts that come with B&B are much larger...

The bolts that come with B&B are much larger diameter than the original bolts, did you tap out the motor, and use smaller diameter bolts?
Forum: Gas Engines
02-23-2017, 07:08 AM
Replies: 375
Views: 56,981
Posted By john.j.allen

I just take off the spring and use a choke servo.

I just take off the spring and use a choke servo.
Forum: Gas Engines
08-20-2015, 12:33 AM
Replies: 375
Views: 56,981
Posted By john.j.allen

AGM UK website says "product not found" for the...

AGM UK website says "product not found" for the AGM30, and "COMING SOON" for the 60 twin & 64cc single.

Looks like the AGM journey is over
Forum: ARF or RTF
07-21-2015, 06:55 AM
Replies: 8
Views: 3,217
Posted By john.j.allen

I had this problem when using ply spacers to move...

I had this problem when using ply spacers to move the motor forward, I've since switched to washers, and I'm using one washer on the cowl mount to compensate for the right/down thrust. It still does...
Forum: Gas Engines
04-16-2015, 04:00 AM
Replies: 375
Views: 56,981
Posted By john.j.allen

My AGM30 appears to sport less of the signs of a...

My AGM30 appears to sport less of the signs of a fake DLE30 than my DLE30. They both have the exact same carb, but the DLE30 has the "tell tale" signs in the cylinder casting indicating its a fake.
Forum: Gas Engines
04-15-2015, 04:20 AM
Replies: 375
Views: 56,981
Posted By john.j.allen

Shaft was bent (made that way), new shaft...

Shaft was bent (made that way), new shaft installed, all is good
Forum: Gas Engines
03-31-2015, 04:26 AM
Replies: 375
Views: 56,981
Posted By john.j.allen

Looks like the prop shaft was forced onto the...

Looks like the prop shaft was forced onto the crankshaft at an angle., so right at the hub the prop is ok, but its very visible at the tip of the shaft, and stick a bolt in it, and its exceedingly...
Forum: Gas Engines
03-30-2015, 03:41 AM
Replies: 375
Views: 56,981
Posted By john.j.allen

I have my AGM30 installed in my Peak MXS-R, and I...

I have my AGM30 installed in my Peak MXS-R, and I don't need a tool to check the run-out on the prop shaft, its so bad I can see it by simply turning the prop over. That said the prop seems to be...
Showing results 1 to 9 of 9


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service - Do Not Sell My Personal Information

Copyright 2018 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.