RCU Forums - Search Results

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Notices
Search: Posts Made By: Hardy
Showing results 1 to 19 of 19
Search took 0.64 seconds.
09-04-2013, 12:29 PM
Replies: 13
Views: 3,089
Posted By Hardy

I have been having the same problem with a Ys 63...

I have been having the same problem with a Ys 63 fz . It would dump raw fuel from the carb at about 4000 rpm, but hold the fuel under full tank pressure when the engine was stopped. So I phoned Ys...
Replies: 11
Views: 2,044
Posted By Hardy

RE: Setting endpoint/centerpoint using HFP-20 or programmable Tx

To setup an MXS-R which has large control surfaces to fly IMAC. Which does not need 3D surface deflection. Which method is best, reduce the servo travel by setting the end points in the transmitter...
09-27-2011, 08:05 PM
Replies: 7
Views: 2,058
Posted By Hardy

RE: Dz 160 fuel pump prime

Thank you for the reply apereira. The engine is mounted on a YS supermount. The plane is a mxs-r which I would like to try in IMAC. I have been starting it with a very nearly closed throttle which...
09-26-2011, 09:02 PM
Replies: 7
Views: 2,058
Posted By Hardy

RE: Dz 160 fuel pump prime

Thank you for the reply apereira. Are you using a check valve on your vent line. I put in a long vent line that loops to the back of the tank than excites at the fire wall. I spent some time with the...
09-26-2011, 06:44 PM
Replies: 6
Views: 1,133
Posted By Hardy

RE: YS 110FZ throttle barrel setting

When my 110fz not will start the first thing is a new glow plug. Then test the check valve to see if it is holding pressure. Spin the engine for several minutes than open a the line you fill the tank...
09-26-2011, 11:05 AM
Replies: 7
Views: 2,058
Posted By Hardy

RE: Dz 160 fuel pump prime

Hi apereira Thank you for the response.
I have since researhed some of Troy Newmans articles on the Dz engines and found them very helpful. I have put a clear fuel line between the pump and the...
09-24-2011, 09:22 PM
Replies: 7
Views: 2,058
Posted By Hardy

Dz 160 fuel pump prime

The engine is new and never been run before. The fuel pump will not pick up fuel until you prime the pump. No air in the pump suction line and it will pump. I can pushed fuel through the pump with a...
06-28-2010, 10:51 PM
Replies: 1
Views: 668
Posted By Hardy

DZ 160 exhaust

Which exhaust system works best with a DZ 160
09-22-2009, 11:02 PM
Replies: 5
Views: 1,188
Posted By Hardy

RE: YS 110 Fuel and Such

Petec
Thank you for the info and link.
09-22-2009, 12:29 AM
Replies: 4
Views: 793
Posted By Hardy

RE: ys 110 fuel line

Set up the fuel lines as per the diagram in the FZ110 operator's manual. To run smoke use a smoke oil pump. To fill and depressure the ys system, put a tie and dot in the pressure line between the...
09-21-2009, 11:54 PM
Replies: 5
Views: 1,188
Posted By Hardy

RE: YS 110 Fuel and Such

Troy what is the difference between cool power propattern 25% fuel and coolpower 25%fuel. I run a ys 110 in a Hangar 9 Showtime and love the engine. I have been useing propattern 25%.
09-05-2009, 11:29 PM
Replies: 24
Views: 15,774
Posted By Hardy

RE: Anyone used a Thunder Power 610C charger ?

To me the 610c seemed very hot. The battery voltage was 6.4 volts measured. The cutoff was set at 2.8 volts and discharge rate was 85 ma. The battery type is LiFePo. 2s. The charge cycle seems to...
09-05-2009, 10:46 PM
Replies: 24
Views: 15,774
Posted By Hardy

RE: Anyone used a Thunder Power 610C charger ?

So why should the 610c go in ERROR before it has discharged the LiFePo battery pack to the set cutoff
09-05-2009, 01:20 PM
Replies: 24
Views: 15,774
Posted By Hardy

RE: Anyone used a Thunder Power 610C charger ?

Anyone used the 610c with a LiFePo battery? On a discharge test what does the flashing E mean? The battery volts are above the cutoff but 610c has stopped discharging the battery.
10-12-2007, 12:03 AM
Replies: 31
Views: 5,575
Posted By Hardy

RE: How well did your YS run after sending it in for service?

Hi guys I sent a ys 63 in for repair. I had fuel problem than crashed the plane. The engine was repaired including a new crank. The engine ran so so. So I emailed Dave he recommend heli 30% fuel and...
08-18-2006, 11:29 PM
Replies: 1
Views: 425
Posted By Hardy

Ys 63 throttle management

When you use a Futuba Cap 9 Tx with idle down what rpm should idle down be set to on a YS 63 FZ? It appears to me that the Ys 63 does not like the throttle rapidly cycled when the plane is taxied on...
04-06-2005, 10:48 PM
Replies: 3
Views: 492
Posted By Hardy

RE: Ys 63 FZ fuel regulator

The fuel is XP pro pattern 25 % nitro with 100% syn oil blended to 20% oil content. Thanks for the phone number. I will try some different fuel.
04-06-2005, 12:17 AM
Replies: 3
Views: 492
Posted By Hardy

Ys 63 FZ fuel regulator

I have never been able to get a stable carb setting at rpm just above idle speed. When the engine is shut down with full tank pressure the carb will drip fuel (some times). I have cleaned the...
06-29-2004, 11:58 PM
Replies: 1
Views: 455
Posted By Hardy

YS 63 idle adjustment

I can set the idle for 2000 RPM and it idles along just fine. However when I pick the RPM up to 2400 for about 6 seconds the carb begins to drip fuel. The engine is mounted inverted. The transition...
Showing results 1 to 19 of 19


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service - Do Not Sell My Personal Information -

Copyright 2021 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.