Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Notices
 
Search: Posts Made By: RJConnet
Showing results 1 to 25 of 500
Search took 1.03 seconds.
09-29-2015, 09:38 AM
Replies: 2
Views: 508
Posted By RJConnet

I flew my RCGF 45 on a Aeroworks 35cc Extra 300...

I flew my RCGF 45 on a Aeroworks 35cc Extra 300 ARF QB for a couple years. Thought it was a perfect match, no extra lead for balance. Then one day I was fooling with the Tx and somehow managed to...
Forum: Gas Engines
07-16-2015, 12:23 PM
Replies: 5
Views: 587
Posted By RJConnet

Dan and ahicks, The Carb is a Walbro clone by...

Dan and ahicks, The Carb is a Walbro clone by name of EMAS (same spelled backwards). After reading ahicks response I removed the cover plate and the diaphragm and pin and fork assembly and pulled...
Forum: Gas Engines
07-16-2015, 08:19 AM
Replies: 5
Views: 587
Posted By RJConnet

Forgive my ignorance, is the needle you are...

Forgive my ignorance, is the needle you are refering to the one actuated by the diaphram under the cover with the four screws holding it to the carb body? RJ
Forum: Gas Engines
07-15-2015, 02:40 PM
Replies: 5
Views: 587
Posted By RJConnet

Carb flooding

My Carb is flooding and dripping fuel while refueling. This is a two line system with a tee in the fuel line for refueling. This is the third plane I have used this system and have never had this...
Forum: Gas Engines
05-20-2015, 09:02 AM
Replies: 12
Views: 1,781
Posted By RJConnet

Been flying my AGM 30 on a Aeroworks Extra 260...

Been flying my AGM 30 on a Aeroworks Extra 260 Freestyle for a year now. Starts easy, turns a Xoar 18-8 prop 7800-8000, and idles at 1800. Never a dead-stick (not one), have no complaints............
Forum: Gas Engines
09-23-2014, 01:32 PM
Replies: 11
Views: 2,915
Posted By RJConnet

When I mounted my AGM 30 on my Aeroworks...

When I mounted my AGM 30 on my Aeroworks Freestyle I used the template provided for a DLE 30 and it fit perfectly. By the way, the engine has been great, no problems. It pulls the Freestyle almost as...
Forum: Gas Engines
08-14-2014, 12:16 PM
Replies: 11
Views: 835
Posted By RJConnet

I have also heard what Mike said about switching...

I have also heard what Mike said about switching oils, particularly when switching from a Dino to a synthetic oil (or vice-versa). Any remnants of the original oil left in the fuel tank, fuel lines,...
Forum: Gas Engines
05-14-2014, 02:33 PM
Replies: 8
Views: 1,593
Posted By RJConnet

Today I swapped the muffler back to the original...

Today I swapped the muffler back to the original supplied with the engine. Without any retuning it turned 7900 rpm, but boy was it loud. Then I ground off the crimped portion of the pitts muffler...
Forum: Gas Engines
05-12-2014, 01:43 PM
Replies: 8
Views: 1,593
Posted By RJConnet

The engine is on a AW Freestyle Extra 260 not...

The engine is on a AW Freestyle Extra 260 not flown yet. I ran a couple of tanks through it on the bench before mounting and it seemed to be turning up good at that point with the stock muffler but I...
Forum: Gas Engines
05-11-2014, 06:49 PM
Replies: 8
Views: 1,593
Posted By RJConnet

Dle 30 rpm

What RPM should I expect from a properly broken in DLE 30 with a Xoar 18--8 prop. No in-flight measuments please. I would really appreciate any and all responses.......... RJ
Forum: Gas Engines
05-08-2014, 06:13 PM
Replies: 7
Views: 927
Posted By RJConnet

Wow, that name is a real mouth full, thanks a...

Wow, that name is a real mouth full, thanks a bunch.........RJ
Forum: Gas Engines
05-08-2014, 03:21 PM
Replies: 7
Views: 927
Posted By RJConnet

Muffler sealer

What is the best muffler sealer to use when installing a Pitts muffler without a gasket. All suggestions will be appreciated.
RJ Connet
Forum: ARF or RTF
05-07-2014, 09:39 AM
Replies: 0
Views: 310
Posted By RJConnet

AW Extra 260 Freestyle QBL

I would like to hear from those who have experience with this plane. I got mine fully assembled yesterday, it weighs 11 Lbs. and the tail hangs about a foot lower than the nose when hanging on the CG...
Forum: Gas Engines
04-29-2014, 11:33 AM
Replies: 20
Views: 6,977
Posted By RJConnet

This may not have a lot to do with the OP's...

This may not have a lot to do with the OP's original question but I am curious. It seems to me way back in the dim dark recesses of my mind that Champion used to make two sizes of spark plugs. Back...
Forum: ARF or RTF
03-24-2014, 08:53 AM
Replies: 1
Views: 548
Posted By RJConnet

Pilot 30cc planes

Anybody out there that has any experience with this series of planes. Extra, Edge, Sbach, and so on. The specs read real good but at my age (84) i'm afraid they might be a little fast for what little...
Forum: Gas Engines
03-15-2014, 04:18 PM
Replies: 375
Views: 60,956
Posted By RJConnet

I bought my AGM 30 about 2 months ago and today...

I bought my AGM 30 about 2 months ago and today is the first day it was warm enough to go out in the garage and set it up on the bench. I did use the plug that came with but I used an older 4.8 volt...
Forum: Glow Engines
02-24-2014, 02:23 PM
Replies: 3
Views: 464
Posted By RJConnet

Check your e-mail.......... RJ

Check your e-mail.......... RJ
Forum: ARF or RTF
01-30-2014, 03:19 PM
Replies: 36
Views: 1,751
Posted By RJConnet

I had one of the early GP ARF's, A G202 powered...

I had one of the early GP ARF's, A G202 powered by a Webra 1.20 that was like this. After several attempts to straighten the elevators I finally gave up and let them be different. At neutral one...
10-05-2013, 08:40 AM
Replies: 442
Views: 52,150
Posted By RJConnet

I think it would be great, I flew mine with an...

I think it would be great, I flew mine with an RCGF 45 at 3Lbs. and 10 Oz. and the plane still needed a tiny bit of extra nose weight. If it fits in the cowl I'd go for it..... RJ
Forum: Glow Engines
09-27-2013, 09:29 AM
Replies: 336
Views: 28,382
Posted By RJConnet

Been playing with these toy motors (engines for...

Been playing with these toy motors (engines for you picky ones) for 70 years. In that time I've only run across two (out of 50 or so) that I would call bad. A Perky .09 and a Bullet .29, both...
Replies: 4
Views: 1,009
Posted By RJConnet

AJ, I don't think it will be a problem. I am...

AJ, I don't think it will be a problem. I am running a whole slew of Hitec servos that are spec'd for 4.8 and 6.0 volts on A123 batteries which run a little over 7 volts off the charger. No problems...
Replies: 4
Views: 1,009
Posted By RJConnet

Have not used them yet but the metal box they...

Have not used them yet but the metal box they came in have speed and power specs for both 6 and 7.4 volts printed on the box. Seems like you should be OK......... RJ
Forum: Gas Engines
06-14-2013, 08:53 AM
Replies: 55
Views: 6,428
Posted By RJConnet

RE: opto kill switch

I'm afraid I will have to throw in with Dan on this one. The pictures in Dan's post show very little protection from RF interference. The ignition circuitry is electrically isolated from the receiver...
Forum: Gas Engines
05-12-2013, 12:19 PM
Replies: 9
Views: 806
Posted By RJConnet

RE: What do I do now?

See my post back on page 7 (3/11/130). got the replacement from Bennettbuilt.com
RJ
Forum: Gas Engines
03-13-2013, 03:45 PM
Replies: 8
Views: 1,481
Posted By RJConnet

RE: Carb. fuel inlet nipple

Thanks everbody, what I wound up doing after breaking off the plastic part of the fitting was to take a 4-40 tap and run it into the brass stub that was left. Then I cut a half inch piece of brass...
Showing results 1 to 25 of 500
 


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service - Do Not Sell My Personal Information -

Copyright 2018 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.