RCU Forums - Search Results

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Notices
Search: Posts Made By: tim956ma
Showing results 1 to 17 of 17
Search took 0.24 seconds.
Forum: Marketplace
05-15-2020, 11:58 AM
Replies: 2
Views: 252
Posted By tim956ma

Tim

Would you be willing to sell the old head with the fly bar?
Forum: Marketplace
11-27-2019, 03:51 PM
Replies: 1
Views: 483
Posted By tim956ma

TJ

I would like to buy your engine could you send me the invoice so I can pay through PayPal.
Forum: Marketplace
11-08-2019, 10:49 AM
Replies: 6
Views: 379
Posted By tim956ma

TJ

Will the larger one start a 70cc twin cylinder engine?
Forum: Gas Engines
10-28-2019, 03:44 PM
Replies: 15
TJ
Views: 609
Posted By tim956ma

TJ

I only flew the airplane the one time all the other times the running was on the ground and yes when I do reach under it to open up the choke sometimes the gas is running out from the carburetor...
Forum: Marketplace
10-28-2019, 10:52 AM
Replies: 1
Views: 307
Posted By tim956ma

Tim

Could you tell me approximately how old your engine is and about how many gallons of fuel has been through it and are you the first owner of this engines? Are there any problems with the engine that...
Forum: Gas Engines
10-28-2019, 08:52 AM
Replies: 15
TJ
Views: 609
Posted By tim956ma

TJ

I work on the engine trying to get it started without taking anything apart off and on for about 3 days I did not take the carburetor apart to check anything I would think the company would rather do...
Forum: Gas Engines
10-26-2019, 07:14 PM
Replies: 15
TJ
Views: 609
Posted By tim956ma

TJ

Yes I checked that the choke was lined up and fully closing. Also EME says that they use genuine walbro carburetors and not clones so that shouldn't be the problem the engine runs good once you do...
Forum: Gas Engines
10-26-2019, 03:17 PM
Replies: 15
TJ
Views: 609
Posted By tim956ma

TJ

Yes thanks for all the help and suggestions the needle settings is what the manual says I did check them and where I have them set is where the engine runs the best the spark plugs are the ones that...
Forum: Gas Engines
10-26-2019, 06:29 AM
Replies: 15
TJ
Views: 609
Posted By tim956ma

TJ

I do not know if this matters but the prop size is
2310.
Forum: Gas Engines
10-26-2019, 06:26 AM
Replies: 15
TJ
Views: 609
Posted By tim956ma

TJ

It idles at around 1800 RPMs full power is around 6500 RPMs and the needle valves are set at the factory settings I did recheck them and I did reset the needles on the low end it is set at 1 and 1/2...
Forum: Marketplace
10-25-2019, 01:06 PM
Replies: 5
Views: 601
Posted By tim956ma

TJ

Do you have a muffler for the DA50?
Forum: Gas Engines
10-25-2019, 12:28 PM
Replies: 15
TJ
Views: 609
Posted By tim956ma

TJ

I just bought a EME 70 twin a few months ago but I just know got around to putting it on the airframe the problem I am having is it is hard to start it is getting fuel to the carburetor but I have to...
Forum: Marketplace
10-23-2019, 10:34 PM
Replies: 2
Views: 838
Posted By tim956ma

Tim

How much for the airplane in the video?
Forum: Marketplace
10-12-2019, 07:49 PM
Replies: 3
Views: 1,404
Posted By tim956ma

Tim

what servos is in the plane?
Forum: Marketplace
09-03-2019, 05:16 PM
Replies: 0
Views: 199
Posted By tim956ma

Airplane accessories

Cowl and canopy
07-29-2019, 03:31 AM
Replies: 8
Views: 4,752
Posted By tim956ma

Yellow aircraft Cap 10B

I also have a yellow aircraft cap 10B I've had for about six years or so still in the box I would like to build someday.
Forum: The Clubhouse
06-06-2013, 08:53 AM
Replies: 130
Views: 6,705
Posted By tim956ma

RE: Should I get a pilots license?

http://www.rcuniverse.com/forum/js/fckeditor/editor/images/smiley/msn/thumbs_up.gifIf this is something you think you would like to do i say yes. I got mine at age 33 i rented planes for a while then...
Showing results 1 to 17 of 17


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service - Do Not Sell My Personal Information

Copyright 2018 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.