Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Notices
 
Search: Posts Made By: Dale_L
Showing results 1 to 25 of 96
Search took 0.97 seconds.
Forum: 3D Flying!
11-03-2003, 09:38 AM
Replies: 3,517
Views: 393,000
Posted By Dale_L

RE: UCD

I & C,

I am using the stock tank with my YS 120. I did wrap the tank once the around the long ways and in two places on the sides. You will just need to open up the formers in the fuse a bit for...
Forum: 3D Flying!
10-28-2003, 10:43 AM
Replies: 3,517
Views: 393,000
Posted By Dale_L

RE: U Can Do 3D

Well Joe, if the offset is 1/16" = 0.0625" over 4.5", then .0625/4.5 = sin(offset angle). So, (offset angle) = arcsin(0.0625/4.5) = 0.8°. I don't think that this offset makes a whole heck of a lot...
Forum: 3D Flying!
08-14-2003, 07:27 PM
Replies: 3,517
Views: 393,000
Posted By Dale_L

RE: Belly Pan

Thanks, guys. Yea, I know it is really easy to build one, but if someone had a crashed UCD and I didn't have to build one, that would be great. Call me lazy......

DL
Forum: 3D Flying!
08-14-2003, 05:18 PM
Replies: 3,517
Views: 393,000
Posted By Dale_L

Belly Pan

In the same vein as the canopy, does anyone have a belly pan? It could be used or new. The plane just looks funny without it.

Dale
07-24-2003, 04:07 PM
Replies: 8
Views: 854
Posted By Dale_L

YES!!! Ding, Ding, Ding

Lenny,

That is a winner. This is the one I was looking for. Thanks.

Dale
07-24-2003, 02:58 PM
Replies: 8
Views: 854
Posted By Dale_L

Built up pull/pull kit

Ralph,

Thanks for the link. I knew about SWB, but I am looking for a tray that is built from wood and not an anodized metal one.

Dale
07-24-2003, 02:12 PM
Replies: 8
Views: 854
Posted By Dale_L

Built up pull/pull kit

What I am looking for is a commercial kit that someone is selling. You could get it with 4" or 5" bellcranks and they will sell you a pre-built tray or the kit where you build the tray.

Thanks,
...
07-24-2003, 01:17 PM
Replies: 8
Views: 854
Posted By Dale_L

Built up pull/pull kit

I am looking for a built up laser cut pull/pull rudder servo kit for 35% and 40% aircraft. I saw one online somewhere, but for the life of me I can't remember where. The kit came with laser cut wood,...
Forum: 3D Flying!
07-09-2003, 03:55 PM
Replies: 3,517
Views: 393,000
Posted By Dale_L

Firewall construction

Here was my firewall experience: http://www.rcuniverse.com/showthread.php?postid=227221#post499708

From what I remember of the firewall, just the usual tab style interlocking. When mine was off, I...
Replies: 73
Views: 5,137
Posted By Dale_L

Rf Module

WreckR,

I forgot :rolleyes: that I once had to solder the pins for my Rf module (8UAF). One or two of the pins came loose from bad solder joints and my removing the Rf module to adjust the...
Replies: 73
Views: 5,137
Posted By Dale_L

Futaba 9C Range Problems...

WreckRman, I agree with you. I know I always go for @ least 100ft. This is probably redundant, but make sure you are not pointing your antenna directly at the plane. That is the weakest part of the...
Forum: Glow Engines
04-14-2003, 01:18 PM
Replies: 14
Views: 1,057
Posted By Dale_L

Tapered sleeve

Mel,

I don't know about your engine exactly, but if it has a removable cylinder sleeve, take a look at the bottom end of it. All the sleeves that I have run into have a tapered bottom. Lube the...
Forum: Kit Building
03-31-2003, 01:25 AM
Replies: 75
Views: 5,915
Posted By Dale_L

Yet Another Ohio Model Planes Giant Scale Edge 540 Profile Build Thread

Moses,

Everything is fine. The center section has a taper to it. Were I to do it again, I would modify the center section to match the inboard rib of the wing. If you notice, they don't match. I...
03-25-2003, 01:57 PM
Replies: 3
Views: 485
Posted By Dale_L

OMP GS540P...flew it today!!

Sounds so fun. Mine is close too. Gotta finish covering the fuse and install all the servos, linkages, engine (Moki 2.1) and tank. Snow has been heavy, so I have not been that motivated to finish and...
03-20-2003, 01:01 AM
Replies: 7
Views: 688
Posted By Dale_L

Rubber Duck Antenna

I like it a lot. I have no range problems with anything electric to glow and even single conversion receivers and I don't have to be concerned about getting it in the prop. Only bad part is it does...
03-19-2003, 10:23 PM
Replies: 7
Views: 688
Posted By Dale_L

What to do with a snow day

No prop breakage today!!!:cool: This was a ball today.
03-19-2003, 10:22 PM
Replies: 7
Views: 688
Posted By Dale_L

03-19-2003, 10:21 PM
Replies: 7
Views: 688
Posted By Dale_L

What to do with a snow day

Here is what it looks like outside right now.....
Forum: Glow Engines
03-19-2003, 02:29 PM
Replies: 11
Views: 965
Posted By Dale_L

.25 opinions

For weight/power/ease of use, go with an OS 25FX, IMO. They run great right out of the box every time. Put a mousse can on and on 15%, they spin 17.5k on an APC 9X4 and start first flip almost every...
Forum: 3D Flying!
03-17-2003, 12:26 AM
Replies: 50
Views: 3,071
Posted By Dale_L

Start 'em Young

Think 2 1/2 is too young to start them? This pic came out so well, that I just wanted to share it. :D Maybe he will be the next Chip Hyde.......

Dale
Forum: Kit Building
03-07-2003, 02:15 PM
Replies: 75
Views: 5,915
Posted By Dale_L

Yet Another Ohio Model Planes Giant Scale Edge 540 Profile Build Thread

Karl,

I just taped a couple sheets of 8.5" X 11" paper together end to end cut it in half the long way and rolled them around a 0.5" dowel. I tacked the end with thin CA and stuck the dowel/paper...
02-28-2003, 01:38 PM
Replies: 14
Views: 873
Posted By Dale_L

First Profile Plane

Background UCD 3D. What's the prize?
02-15-2003, 03:47 AM
Replies: 366
Views: 37,293
Posted By Dale_L

Ohio Model Edge 540 Giant Profile

All up weight.......
Forum: Kit Building
02-08-2003, 03:55 PM
Replies: 83
Views: 7,345
Posted By Dale_L

Ohio Model Edge 540 Giant Profile My Build

Roger,

Ditto on the sheeting. I was able to get away with 1 36" sheet. For the trailing edge sheeting, I glued 2 pieces together. That lonly eft me short 2 10" sections. If I used full sections...
Forum: Kit Building
02-03-2003, 04:28 PM
Replies: 83
Views: 7,345
Posted By Dale_L

Ohio Model Edge 540 Giant Profile My Build

Mike,

I ran in to exactly what Roger is talking about with being short of wood. My problem is that my left over balsa stock is very low and I have not replenished it. That means that every time I...
Showing results 1 to 25 of 96
 


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service - Do Not Sell My Personal Information -

Copyright 2018 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.