Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Notices
Search: Posts Made By: Kostas1
Showing results 1 to 12 of 12
Search took 0.02 seconds.
04-10-2017, 11:20 PM
Replies: 11
Views: 2,987
Posted By Kostas1

For the electronics I used: 2 18650 Samsung...

For the electronics I used:

2 18650 Samsung Li-Ion batteries @ 2.200mAh
2 charging boards for Li-Ion's tp4056 @ 1A
1 3 Pole Double Pole Double Throw
1 dc-to-dc step-up converter
1 small button...
04-10-2017, 11:14 PM
Replies: 11
Views: 2,987
Posted By Kostas1

:cool:

:cool:
04-10-2017, 11:13 PM
Replies: 11
Views: 2,987
Posted By Kostas1

And then comes the paint!

And then comes the paint!
04-10-2017, 11:11 PM
Replies: 11
Views: 2,987
Posted By Kostas1

Here I sand the outside of the box with a very...

Here I sand the outside of the box with a very fine sandpaper to prepare it
for a 2 coat 2 colour spray paint.
04-10-2017, 11:10 PM
Replies: 11
Views: 2,987
Posted By Kostas1

Box cover!

Box cover!
04-10-2017, 11:05 PM
Replies: 11
Views: 2,987
Posted By Kostas1

This is the cover of the acrylic box. As you...

This is the cover of the acrylic box.
As you see I made two diagonal tabs to serve as balancers of the top part.
04-10-2017, 11:04 PM
Replies: 11
Views: 2,987
Posted By Kostas1

Continuing!

Continuing!
04-04-2017, 12:05 AM
Replies: 11
Views: 2,987
Posted By Kostas1

Here are the plexiglass parts after the cutting! ...

Here are the plexiglass parts after the cutting!

I used Medium CA+ to glue the pieces together and a couple psitsssss of CA Activator!
04-03-2017, 11:57 PM
Replies: 11
Views: 2,987
Posted By Kostas1

The saw cuts the plexiglass nice & clean, but...

The saw cuts the plexiglass nice & clean, but ofcourse it needs a little bit of sanding!!!

I also made a sanding block from some particle board I had laying arround.
04-03-2017, 11:53 PM
Replies: 11
Views: 2,987
Posted By Kostas1

I also bought a nice holder/grip that is extra...

I also bought a nice holder/grip that is extra NO-slippery from ebay!
04-03-2017, 11:51 PM
Replies: 11
Views: 2,987
Posted By Kostas1

I started my build, buying a third-hand helping...

I started my build,
buying a third-hand helping tool.

This is so handy when it comes to soldering etc!
I bought a piece of 3mm plexiglass and a nice Stanley FatMax saw....
03-28-2017, 11:41 AM
Replies: 11
Views: 2,987
Posted By Kostas1

Handheld bryshless gimbal DIY presentation!

Hey there!!!

I'd like to make a presentation of my handheld gimbal,
for stable video shooting.
I used a cheap 2 axis brushless gimbal.

The project included many different aspects of "design"...
Showing results 1 to 12 of 12


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service - Do Not Sell My Personal Information -

Copyright 2021 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.