Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Notices
Search: Posts Made By: Iflyit
Showing results 1 to 15 of 15
Search took 0.06 seconds.
11-30-2006, 12:21 AM
Replies: 288
Views: 37,031
Posted By Iflyit

RE: Solutions

Any chance of geting a set cut I could buy? :)
11-29-2006, 10:25 PM
Replies: 288
Views: 37,031
Posted By Iflyit

RE: Solutions

Where did you get the laser cut parts?
12-19-2005, 02:22 AM
Replies: 288
Views: 37,031
Posted By Iflyit

RE: Solutions

Well it was 3 years ago when I built my last one, I sold it a while back and have been kicking myself since. I decided to build another one, got it mostly framed up today. Ill post some finished pics...
11-27-2002, 04:16 AM
Replies: 288
Views: 37,031
Posted By Iflyit

Outlaw Construction

http://www.ecubedrc.com
11-06-2002, 03:29 AM
Replies: 288
Views: 37,031
Posted By Iflyit

Outlaw Construction

So its launched at that angle? not even level?? seems that would be alot harder than launching it level. Robert Vess fly's at my club and I have seen him launch his with the fin and it just goes...
11-06-2002, 12:51 AM
Replies: 288
Views: 37,031
Posted By Iflyit

Re: Outlaw Launching

Ive never seen one launched by the wing tip. seems like it could be rather exciting :) Ive always seen them launched by the vert fin by just pushing it away. seems to work, im going to try that this...
11-05-2002, 04:17 AM
Replies: 288
Views: 37,031
Posted By Iflyit

Outlaw Construction

Im just curious, how is everyone launching theirs? just grabbing the fin and letting it go?
11-04-2002, 02:13 AM
Replies: 288
Views: 37,031
Posted By Iflyit

Outlaw Construction

No video today, got one more flight in on it though. Here is a pic.
11-03-2002, 06:15 PM
Replies: 288
Views: 37,031
Posted By Iflyit

Outlaw Construction

85% expo and about 3/4 inch on the low rates, on high rates i have as much as I can get which is about 45 degrees :)
11-03-2002, 04:35 AM
Replies: 288
Views: 37,031
Posted By Iflyit

Outlaw Construction

I flew mine today, got 2 flights in on it. The thing really smokes :)
I had a friend trying to videotape it and he couldnt keep it in the picture LOL

The roll rate is unbelievable as its just a...
10-24-2002, 10:58 PM
Replies: 288
Views: 37,031
Posted By Iflyit

Outlaw Construction

OK, so you cut the balsa out to replace t with 1/16 ply. According to the instructions, the whole area between ribs 1 is to be sheeted with 1/16 ply?
10-23-2002, 11:36 PM
Replies: 288
Views: 37,031
Posted By Iflyit

Re: Solutions

Im still confused at this part? where exaclty does the 1/16 ply go? on top of the bottom sheeting, or do you cut the balsa sheeting to put it in place of it?
10-23-2002, 07:57 PM
Replies: 288
Views: 37,031
Posted By Iflyit

Outlaw Construction

according to the directions, that is the right way, to cut completely thru it and slip the rudder down it looks like.

So did you sheet the bottom between ribs 1 with ply?
10-23-2002, 07:07 PM
Replies: 288
Views: 37,031
Posted By Iflyit

Outlaw Construction

I am at the point in building mine that it says to put the ply cover on the bottom between ribs 1. Does this mean you just sheet it with 1/16 ply between ribs 1?

Also, Where does the ply doubler...
10-10-2002, 02:26 AM
Replies: 288
Views: 37,031
Posted By Iflyit

Outlaw Construction

What motor mount is recommended for the webra 32? part #?
Showing results 1 to 15 of 15


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service - Do Not Sell My Personal Information -

Copyright 2018 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.