RCU Forums - Search Results

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Search: Posts Made By: Dan 2000
Showing results 1 to 12 of 12
Search took 0.59 seconds.
01-22-2008, 07:50 PM
Replies: 4
Views: 643
Posted By Dan 2000

RE: F 1 Tunnel hull

Can you tell me what engine you are using.My Sprint Catamaran with a Stock Zenoah.The prop shaft center line was at the bottom of the sponsons.But for a F-1 Tunnel Hull i would think take the prop...
01-22-2008, 04:28 PM
Replies: 5
Views: 754
Posted By Dan 2000

RE: need some help

May i ask how Fast do you want to go?Take Care, Dan
01-22-2008, 04:20 PM
Replies: 27
Views: 2,664
Posted By Dan 2000

RE: Best Radio Box?

I also have in the past used outdrives furnished by MHZ USA. I would recommend using at least a 1/4 scale servo.Turning both at the same time can be tricky setup.You could always use two...
01-21-2008, 09:59 PM
Replies: 13
Views: 938
Posted By Dan 2000

RE: choppy seas

I was thinking about Racing In Choppy Seas.Have you looked at MHZUSA.com lately? There is Hulls in any size.What i would do is call them and ask.Tell them what size power plant you want to...
01-21-2008, 08:38 PM
Replies: 13
Views: 938
Posted By Dan 2000

RE: choppy seas

Any RC Boat over 50 inches will handle Choppy Seas.Remember More Free Board is Better.Alot less water entering the Hull.WareHouse Hobbies Manta -Ray ,Can go 60 mph with the Right Size Engine.I have...
01-21-2008, 02:24 PM
Replies: 26
Views: 2,237
Posted By Dan 2000

RE: aeromarine or warehouse hobbies


For myself i have been in RC Boats since 1970.I remember most of the RC Boat Hulls were few in between for Gas Motors.
I have a 3D Viper Boat,42 inches by 12 inches by 3 inches...
11-27-2003, 10:02 AM
Replies: 33
Views: 10,663
Posted By Dan 2000

RE: 4 stroke boat motors??

Back in the early 70's a american man buildt a 350 chevy engine that sold for about 1500.00 dollars The pistons were the size of a dime.Any No where to find
a beauty?Dan2000
11-27-2003, 09:55 AM
Replies: 4
Views: 1,187
Posted By Dan 2000

RE: Pro Boat Shockwave

How fast are willing to drive? Go to www.marine specialties an download Boat versus boat propellar pitch guide.For a given propellar you can by RPM's get a rough estimate on how fast your boat can...
11-27-2003, 09:47 AM
Replies: 1
Views: 1,338
Posted By Dan 2000


Yes i would believe it is a header pipe for your engine.Take care Dan
11-27-2003, 09:43 AM
Replies: 6
Views: 1,753
Posted By Dan 2000

RE: Pro Boat Shock Wave

I have a quick draw pipe wrap to center.On a 260 full modified.My boat after trimming whent 40 miles an hour.A little to loose for a shallow deep vee
that is 42" inches long.It would go alot faster...
11-27-2003, 09:37 AM
Replies: 3
Views: 1,828
Posted By Dan 2000

RE: Expresscraft Osprey -- Nice Pics

I can only wish that in time i could use my SATA Jet B to paint one of my next boats.I am not a custom painter but i wll try.May i ask how much did that paint job cost you? Take Care Dan
11-27-2003, 09:25 AM
Replies: 76
Views: 11,754
Posted By Dan 2000

RE: What kind of gas boats do you have?

I have buildt many speed boats,mostly in Gas.I haved buildt an ran Nitro as for engines as Picco's 80's and CMB- 90's.Square Head designes.I buildt a speed boat that i traded to my brother for aHP...
Showing results 1 to 12 of 12

Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service - Do Not Sell My Personal Information -

Copyright 2021 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.