Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Notices
Search: Posts Made By: dvines
Showing results 1 to 25 of 25
Search took 0.05 seconds.
Forum: Kit Building
09-13-2019, 03:11 PM
Replies: 1
Views: 633
Posted By dvines

ace 4-60 bipe

looking for plans for the ace 4-60 bipe
Replies: 0
Views: 202
Posted By dvines

hobby zone

Looking for a hobby zone FM 3 channel radio frequency 27.195M channel 5 radio
Forum: Glow Engines
10-14-2017, 11:34 AM
Replies: 3
Views: 456
Posted By dvines

Asp 32

Asp 32
Forum: Glow Engines
10-14-2017, 08:19 AM
Replies: 3
Views: 456
Posted By dvines

Main Needle Valve Ratchet Spring

will a main needle ratchet spring from a os engine fit a asp engine?
04-15-2017, 02:20 PM
Replies: 6
Views: 2,598
Posted By dvines

Bud Nosen

Thanks for the instructions This cub will be the Navy NE-1
04-11-2017, 07:13 PM
Replies: 1
Views: 584
Posted By dvines

bud nosen cub

Looking for instructions for bud nosen 1/4 scale cub
04-10-2017, 12:19 PM
Replies: 6
Views: 2,598
Posted By dvines

bud nosen cub

anybody know where I can get a copy of the building instructions for the bud nosen 1/4 scale j-3 cub?
Forum: Sport Flying
02-20-2017, 12:55 PM
Replies: 371
Views: 63,716
Posted By dvines

Did the orginal Midwest 60 size ugly stick have...

Did the orginal Midwest 60 size ugly stick have balsa wing ribs or lite ply? Did it use rubber bands to hold the wing on ?
Forum: Sport Flying
02-17-2017, 12:12 PM
Replies: 371
Views: 63,716
Posted By dvines

scratch building a giant stick is my ryobi 31cc...

scratch building a giant stick is my ryobi 31cc too small? plane weights in around 12-18 pounds
01-20-2017, 09:56 AM
Replies: 7
Views: 450
Posted By dvines

I am using 3/4 inch particle board as my table...

I am using 3/4 inch particle board as my table top I was using 1/2 sheetrock to pin plane down on but now it has ridges in it and is no longer flat I need something I could use instead
01-20-2017, 09:01 AM
Replies: 7
Views: 450
Posted By dvines

build table

I have a piece of 1/2 sheetrock on top of my build table I noticed thre are ridges appearing in it now it is no longer flat does anybody have any ideas what I could use in place of the sheetrock?
09-27-2016, 02:15 PM
Replies: 4
Views: 600
Posted By dvines

April 1995 RCModeler plan # 1189

April 1995 RCModeler plan # 1189
09-26-2016, 12:05 PM
Replies: 4
Views: 600
Posted By dvines

Cessna L-19

I am scratch building the L-19 from the RCM plans I don't have any building instructions it calls for 1/8 shims around the elevator and rudder anybody have any idea what they are for?
Forum: Beginners
08-05-2016, 07:04 AM
Replies: 3
Views: 475
Posted By dvines

pushrods

are 2-56 pushrods too small for the liddle stick with a .30 size engine?
Forum: Sport Flying
07-16-2016, 11:27 AM
Replies: 371
Views: 63,716
Posted By dvines

I found a video on youtube of a r/c club in New...

I found a video on youtube of a r/c club in New Zealand and they had a giant stick with a turboprop on it it didn't look like a rolling take off this thing leaped off the ground
07-11-2016, 11:35 AM
Replies: 3
Views: 490
Posted By dvines

Templete

What is the best material to use to trace the patterns on to?
Forum: Sport Flying
06-18-2016, 02:57 PM
Replies: 371
Views: 63,716
Posted By dvines

the ugly stick was the first plane I learned to...

the ugly stick was the first plane I learned to fly on it was a midwest kit had a saito 65 4 stroke on it
Forum: Gas Engines
06-18-2016, 09:22 AM
Replies: 9
Views: 8,721
Posted By dvines

I am putting a 18cc gas engine on a .60 ugly...

I am putting a 18cc gas engine on a .60 ugly stick is that too much motor?
Forum: Sport Flying
06-18-2016, 09:16 AM
Replies: 371
Views: 63,716
Posted By dvines

is 18cc gas to big for a 60 size stick?

is 18cc gas to big for a 60 size stick?
Forum: Sport Flying
06-18-2016, 08:58 AM
Replies: 371
Views: 63,716
Posted By dvines

I went to outerzone.uk.com and download a couple...

I went to outerzone.uk.com and download a couple of stick plans to build you might check there the plans are free
Forum: Gas Engines
06-14-2016, 04:10 PM
Replies: 4
Views: 901
Posted By dvines

25cc gas engine

a 25cc gas engine is equivalent to what size glow engine?
06-14-2016, 02:11 PM
Replies: 3
Views: 1,604
Posted By dvines

prop hubs and motor mounts

now that wackerengines and carr precision have gone belly up does anybody know of anybody else that makes prop hubs an motor mounts for the ryobi engine ? Yes DR Tune quit too
06-14-2016, 02:01 PM
Replies: 0
Views: 308
Posted By dvines

prop hubs and motor mounts

wackerengines and carrpercision have gone belly up does anybody know of any place else that make prop hubs and motor mounts for the ryobi engines?
06-13-2015, 03:26 PM
Replies: 84
Views: 28,331
Posted By dvines

6' pt boat

would you happen to know where to find the plans for that boat?
06-03-2015, 02:36 PM
Replies: 17
Views: 2,540
Posted By dvines

Wacker Engines

go back to the hellotrade website and click on products and services and it will take you their website
Showing results 1 to 25 of 25


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service - Do Not Sell My Personal Information -

Copyright 2018 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.