Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Notices
 
Search: Posts Made By: AWorrest
Showing results 1 to 25 of 500
Search took 0.99 seconds.
Replies: 9
Views: 468
Posted By AWorrest

Matt, The MOTO SYSTEM menuís name can lead...

Matt,

The MOTO SYSTEM menuís name can lead to confusion. In my opinion it would have been better if it had been called MOTO HOLD function. When the MOTO SYSTEM (HOLD) is ON, the device controlling...
Replies: 9
Views: 468
Posted By AWorrest

Matt, If the XG11 software has another...

Matt,

If the XG11 software has another update, the addition of a position-switch on the sliders would not only be helpful for timer purposes but also safety. When a slider is used for motor...
Replies: 9
Views: 468
Posted By AWorrest

Deleting a model is the only way I know of...

Deleting a model is the only way I know of resetting the functions/menus to their default condition with the exception of program mixes. Most functions that take a numerical input has zero as their...
Replies: 9
Views: 468
Posted By AWorrest

I doubt that is the case. Have you checked the...

I doubt that is the case. Have you checked the flap rate menu in the function list to see if the flap rates are something other than zero? This is an easy oversight when programming in the GLID...
Replies: 2
Views: 254
Posted By AWorrest

If you’re comfortable with opening up the...

If you’re comfortable with opening up the transmitter, check the fuse. It’s probably not the problem but it is an easy thing to check. The fuse is a 3A normal fuse.

Allan
06-03-2020, 04:42 PM
Replies: 10
Views: 743
Posted By AWorrest

As mentioned before I don’t have an 831B receiver...

As mentioned before I don’t have an 831B receiver but rather an RG731BX which uses the same remote antenna and case as the 831B. When my 731BX receiver is placed in bind mode with the transmitter...
05-30-2020, 01:32 PM
Replies: 10
Views: 743
Posted By AWorrest

Correction: Working with the 731BX a little...

Correction:

Working with the 731BX a little more after making the previous post, I was too hasty in stating the main unit blue LED would not light unless the remote unit was connected. It will...
05-29-2020, 11:58 AM
Replies: 10
Views: 743
Posted By AWorrest

Is the remote antenna connected to the receiver?...

Is the remote antenna connected to the receiver? On the RG731BX which I believe is based on the 831 design, the receiver blue LED will not light and it will not bind unless the remote is connected.
...
04-25-2020, 03:27 PM
Replies: 22
Views: 1,918
Posted By AWorrest

Both the XG11 and XG14 can be set up for a bipe...

Both the XG11 and XG14 can be set up for a bipe with crow. The same should hold true for the DFA/JR T-series. Quique Somenzini did it on his Beast using a 12X. The same setup works on the XG 11 and...
04-22-2020, 03:19 PM
Replies: 22
Views: 1,918
Posted By AWorrest

I have both an XG14 and an XG11MV. Comparing the...

I have both an XG14 and an XG11MV. Comparing the programming for the two is like comparing apples and oranges. There are things one can do and the other can’t. The eleven has more timers and stick...
Replies: 2
Views: 185
Posted By AWorrest

To program the 9503 properly, dual flying...

To program the 9503 properly, dual flying surfaces (ailerons, elevators, rudders and flaps) should be set up with the WING TYPE menu in the Function List and not by using a program mix. Doing...
02-02-2020, 03:41 PM
Replies: 3
Views: 807
Posted By AWorrest

After you have finished the initial steps of...

After you have finished the initial steps of setting the Type selection, Model Name Input, Wing Type Selection/Dual Aileron Selection, and V-tail Selection go to System List and select the Wing Type...
Replies: 9
Views: 557
Posted By AWorrest

What you described is the 12X, not the 12XMV. The...

What you described is the 12X, not the 12XMV. The back cover of the 12X was not meant to be removed. JR never sold to the public anything that could be put into the transmitter by way of the back...
Replies: 9
Views: 557
Posted By AWorrest

I’m quite familiar with the JR 12XMV! I have...

I’m quite familiar with the JR 12XMV! I have owned one since they first came out and still have it.

In your original post you asked about a module. Now you are talking about a circuit board.
...
Replies: 9
Views: 557
Posted By AWorrest

The JR 12X is not a module transmitter. Its rf...

The JR 12X is not a module transmitter. Its rf board is internal. The 12XMV transmitter on the other hand, does use modules. The DSM2/DSMX and 72MHz modules for it are unique and don’t fit any...
01-25-2020, 01:31 PM
Replies: 3
Views: 807
Posted By AWorrest

Take a look at page 72 of the XG8 manual. After...

Take a look at page 72 of the XG8 manual. After you have finish the initial steps of setting the Type selection, Model Name Input, Wing Type Selection/Dual Aileron Selection, and V-tail Selection...
12-02-2019, 12:58 PM
Replies: 8
Views: 1,347
Posted By AWorrest

It has been several years since I had an X9303...

It has been several years since I had an X9303 but on my other JR transmitter with a DSM module there is only a brief period the light on the back would flash during the binding process. It is...
11-30-2019, 01:37 PM
Replies: 6
Views: 1,735
Posted By AWorrest

Since you didnít mention any specific brand of...

Since you didnít mention any specific brand of transmitter, I keep to some general comments about flaperons. On a powered plane with full length ailerons (strip ailerons), flaperons should be used...
11-30-2019, 01:03 PM
Replies: 8
Views: 1,347
Posted By AWorrest

A couple of things you said makes me wonder...

A couple of things you said makes me wonder exactly what equipment you are using. First, you mention the green LED. If you are referring to the LED on the back, all DSM modules and transmitters Iíve...
Replies: 6
Views: 699
Posted By AWorrest

Spektrum is the only brand that authentically has...

Spektrum is the only brand that authentically has the DSM2/DSMX protocol. They are vigilant in keeping it for themselves. In the past JR Propo used it but under licence. When JR Propo parted ways...
11-13-2019, 01:14 PM
Replies: 14
Views: 2,654
Posted By AWorrest

That tip is most likely a misprint. The XG14 came...

That tip is most likely a misprint. The XG14 came out about three years after the XG11. The description of the stick position switches in the XG14 manual is identical to the XG11 except for the...
11-10-2019, 03:10 PM
Replies: 14
Views: 2,654
Posted By AWorrest

You need more stick-position switches on your...

You need more stick-position switches on your XG14 or an XG11 to accomplish what you are asking. Without using two stick-position switches, the only alternatives I can think of are either to use...
08-20-2019, 03:07 PM
Replies: 2
Views: 1,261
Posted By AWorrest

Attached is the instruction for switching the...

Attached is the instruction for switching the AUX1 channel to an XBus port and back for the JR RG613BX receiver. To the best of my recollections, there never was an RG613B (without the X on the end)...
Replies: 10
Views: 1,029
Posted By AWorrest

Be certain that the servos and the battery...

Be certain that the servos and the battery connectors are oriented correctly. I’ve had servos that twitch if the polarity was wrong. Also check that the transmitter modulation is set to PPM.
Allan
07-08-2019, 12:59 PM
Replies: 12
Views: 1,801
Posted By AWorrest

Do you have the instruction sheet for your...

Do you have the instruction sheet for your RG812BX receiver? If the XBus port on your receiver can drive an ordinary servo, the port hasnít been changed from being an ordinary PWM servo port to being...
Showing results 1 to 25 of 500
 


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service - Do Not Sell My Personal Information -

Copyright © 2018 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.