RCU Forums - Search Results

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Notices
Search: Posts Made By: FIDALGO JIM
Showing results 1 to 14 of 14
Search took 0.64 seconds.
Forum: Gas Engines
04-27-2009, 04:17 PM
Replies: 893
Views: 115,870
Posted By FIDALGO JIM

RE: CRRC 40cc kit

I want to weigh in on the POSITIVE side. Bought from Jim at AGAPE also but have had NO porblems . Engine runs great on 18 X 10 or 20 X 8 props. Just ordered another from ABELL hobbies - $210 SHIPPED.
Forum: Glow Engines
02-01-2006, 03:43 PM
Replies: 5
Views: 748
Posted By FIDALGO JIM

RE: ST G4500 inverted?

RE: CONVERSION TO GAS/IGNITION

MINE WAS DONE (BY CH) AT LEAST 6 YEARS BACK BUT THE LAST TIME I BROUGHT UP THE SUBJECT WITH BILL CARPENTER (SAME LAST NAME, NO RELATION WE CAN FIGURE) HE SAID THEY...
Forum: Glow Engines
01-31-2006, 09:38 PM
Replies: 5
Views: 748
Posted By FIDALGO JIM

RE: ST G4500 inverted?

THE ONLY TROUBLE WITH RUNNING A G4500 INVERTED IS THE INITIAL FUEL DRAW/PRIMING - NO CHOKE, AND THE CARB IS IN THE REAR OF THE CRANKCASE. ONCE PRIMED IT RUNS FINE.

I'VE BEEN RUNNING ONE...
Forum: Glow Engines
07-27-2005, 09:02 PM
Replies: 5
Views: 666
Posted By FIDALGO JIM

RE: NEED HELP...MDS .78

ALL I CAN SAY IS THAT MY MDS .78 RUNS DEPENDABLY AND IS VERY USER FRIENDLY.
Forum: Seaplanes
02-03-2004, 11:22 AM
Replies: 9
Views: 1,284
Posted By FIDALGO JIM

RE: SEAMASTER

THANKS! THANKS! THANKS!

JIM
Forum: Seaplanes
02-02-2004, 04:31 PM
Replies: 9
Views: 1,284
Posted By FIDALGO JIM

RE: SEAMASTER

HI!
I'VE BEEN TRYING TO LOCATE A COUPLE OF FIBERGLASS COWLS FOR A CONVERSION OF MY OLD STICK SEAMASTER 120 TO A TWIN. I'VE TRIED ACE, FIBERGLASS SPECIALTIES , TOWER, QUANTUM , ETC WITH NO LUCK....
Forum: Glow Engines
01-12-2004, 11:13 AM
Replies: 3
Views: 667
Posted By FIDALGO JIM

RE: MDS 1.48 ENGINE MOUNTS-WHICH TO USE

;)

MANY THANKS FOR THE INFO AND ADVICE. I'LL LET YOU KNOW THE OUTCOME.:)
Forum: Glow Engines
01-11-2004, 12:49 PM
Replies: 3
Views: 667
Posted By FIDALGO JIM

MDS 1.48 ENGINE MOUNTS-WHICH TO USE

WELL, I'VE BIT THE BULLET AND BOUGHT TWO NIB MDS 1.48 TO USE IN A TWIN CONFIGURATION. I'VE READ ALL THE THREADS AND THINK I HAVE THE INFO TO MAKE IT A SUCCESS. BUT I HAVEN'T READ ANYTHING ABOUT...
Forum: Glow Engines
01-04-2004, 05:07 PM
Replies: 3
Views: 872
Posted By FIDALGO JIM

RE: SEEKING A "TARTAN 44cc ENGINE

I DON'T TOTALLY DISAGREE WITH THE PREVIOUS NEGATIVE POSTS CAUSE I HAD ONE TARTAN TWIN ON GLOW THAT WAS REALLY STRONG BUT VERY CANTANKEROUS AND VERY POOR TRANSITIONING BUT I HAPPEN TO HAVE A TARTAN...
07-04-2003, 01:27 AM
Replies: 2
Views: 530
Posted By FIDALGO JIM

Scale Gear For 1/3 Spacewalker

THANKS-I'LL CHECK THEM OUT.

JIM
07-03-2003, 02:15 PM
Replies: 2
Views: 530
Posted By FIDALGO JIM

Scale Gear For 1/3 Spacewalker

ANYONE KNOW A SOURCE FOR 1/3 SPACEWALKER GEAR? ROBART WEBSITE DOESN'T LIST ANY. BEGINNING TO SUSPECT IT MAY BE CLOSE TO 1/4 CUB GEAR?
Forum: Gas Engines
06-17-2003, 11:11 PM
Replies: 3
Views: 846
Posted By FIDALGO JIM

G62 Prop Recomendation

I REMEMBER THE SAME DISCUSSION FROM SOME TIME BACK AND THE 20 X 8-14 WAS HIGHLY RECOMMENDED BY SOMEONE WHO SEEMED TO BE VERY KNOWLEDGEABLE - BUT AREN'T WE ALL?
Forum: Gas Engines
06-16-2003, 03:22 PM
Replies: 11
Views: 2,615
Posted By FIDALGO JIM

1/3 Scale Spacewalker Engine?

THANKS FELLAS-I DIDN'T THINK I WAS TOO FAR OUT IN LEFT!
Forum: Gas Engines
06-16-2003, 02:03 PM
Replies: 11
Views: 2,615
Posted By FIDALGO JIM

1/3 Scale Spacewalker Engine?

HAVE A NIB SPACEWALKER KIT FOR WINTER PROJECT AND LOOSE G62 WITH CH IGNITION I HAD [PLANNED TO USE . IS THIS TOO MUCH ENGINE FOR THE SPACEWALKER??
Showing results 1 to 14 of 14


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service - Do Not Sell My Personal Information -

Copyright 2021 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.