RCU Forums - Search Results

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Notices
Search: Posts Made By: alfalfa51
Showing results 1 to 18 of 18
Search took 0.02 seconds.
Forum: Marketplace
01-15-2021, 02:26 PM
Replies: 13
Views: 585
Posted By alfalfa51

sixjets, Here is what it should look like...

sixjets,

Here is what it should look like when the raised surface is painted. This is the damaged one that I needed to replace. The trim is about 22 mm wide.
...
Forum: Marketplace
01-11-2021, 01:11 PM
Replies: 13
Views: 585
Posted By alfalfa51

sixjets, Keith at parkflyerplastics has...

sixjets,

Keith at parkflyerplastics has completed the master and molded the Boomerang XL canopy. It was molded from a new unused canopy. He has stock available to ship. The link:
...
Forum: Marketplace
12-30-2020, 02:27 PM
Replies: 13
Views: 585
Posted By alfalfa51

sixjets, I contacted Keith at...

sixjets,
I contacted Keith at parkflyersplastics about the Boomerang XL canopy. He said he does not have but can create a master with a clean part which I happen to have. I am waiting for a reply...
Forum: Marketplace
09-18-2019, 03:54 PM
Replies: 2
Views: 1,018
Posted By alfalfa51

Do you have Vector Tube installed and controlled?

Do you have Vector Tube installed and controlled?
Forum: Marketplace
09-03-2019, 02:09 PM
Replies: 3
Views: 1,272
Posted By alfalfa51

Thanks, let me know.

Thanks, let me know.
Forum: Marketplace
09-03-2019, 02:07 PM
Forum: Marketplace
09-03-2019, 06:24 AM
Replies: 3
Views: 1,272
Posted By alfalfa51

Are you willing to sell the batteries alone?

Are you willing to sell the batteries alone?
Forum: Kit Building
01-05-2019, 02:08 PM
Replies: 3,925
Views: 264,613
Posted By alfalfa51

Thanks for the reply acdii, I did get the...

Thanks for the reply acdii,

I did get the rear doublers installed on the inside. The only gluing I've done to this point is the laminating and the landing gear mount. For now the fuselage is held...
Forum: Kit Building
01-04-2019, 06:59 PM
Replies: 3,925
Views: 264,613
Posted By alfalfa51

Anything I should know about construction or...

Anything I should know about construction or other issues?
Forum: Kit Building
01-04-2019, 06:29 PM
Replies: 3,925
Views: 264,613
Posted By alfalfa51

Has anyone configured a Rascal 168 with a...

Has anyone configured a Rascal 168 with a removable tail? After measuring the 56 inch horizontal it is obvious it won't fit in my van attached to the fuselage.
Forum: Kit Building
01-04-2019, 08:55 AM
Replies: 3,925
Views: 264,613
Posted By alfalfa51

Thanks mogman, I have already laminated the tail...

Thanks mogman, I have already laminated the tail horizontal and vertical. I was going to convert to dual elevator servos but It appears that is a bad idea on this tail heavy airframe.
Forum: Kit Building
01-04-2019, 08:49 AM
Replies: 3,925
Views: 264,613
Posted By alfalfa51

With a little encouragement from Captcrunch44 I...

With a little encouragement from Captcrunch44 I went after the parts that I was having issues with. My concern was that I would weaken an already marginal structure. The suggestion was to sand the...
Forum: Kit Building
01-03-2019, 06:32 PM
Replies: 3,925
Views: 264,613
Posted By alfalfa51

acdii, A limit of five posts per day has kicked...

acdii, A limit of five posts per day has kicked in. This will have to hold over until Friday. It looks like the clock has changed to Friday

I'm not there yet. I can't assemble the main spar, front...
Forum: Kit Building
01-03-2019, 11:14 AM
Replies: 3,925
Views: 264,613
Posted By alfalfa51

PM sent, thanks.

PM sent, thanks.
Forum: Kit Building
01-03-2019, 08:48 AM
Replies: 3,925
Views: 264,613
Posted By alfalfa51

I could not see the front wing mount detail in...

I could not see the front wing mount detail in question. The slots on the laminated front wing mount look similar to what I have but would not match the center rib I have or match the spacing of the...
Forum: Kit Building
01-03-2019, 08:30 AM
Replies: 3,925
Views: 264,613
Posted By alfalfa51

I will visit the build link. I attempted to post...

I will visit the build link. I attempted to post pictures and an explanation but I was denied. The text was with regard to the spacing of the rib slots for the front wing mount. They are not the...
Forum: Kit Building
01-02-2019, 06:58 PM
Replies: 3,925
Views: 264,613
Posted By alfalfa51

Thanks, They did automatically ship me the strut...

Thanks, They did automatically ship me the strut kit a few months after the main kit arrived. My current dilemma involves ribs and spars.
Forum: Kit Building
01-02-2019, 03:33 PM
Replies: 3,925
Views: 264,613
Posted By alfalfa51

Hello, I have been in the hobby for 39 years but...

Hello, I have been in the hobby for 39 years but have not used RCU until now. I post very little on any internet resource. I'm old/retired but still trying to stay in the game. I am in need of...
Showing results 1 to 18 of 18


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service - Do Not Sell My Personal Information -

Copyright 2021 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.