RCU Forums - Search Results

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Notices
 
Search: Posts Made By: muahaha
Showing results 1 to 25 of 500
Search took 0.97 seconds.
Replies: 6
Views: 497
Posted By muahaha

RE: Comp Power Supply

i would not use it for anything else other than computer. The reason is simply b'cos they are not regulated, meaning the amp they deliver is not constant (they fluctuate). This in turn will

a)...
Replies: 9
Views: 500
Posted By muahaha

RE: MOTOR HELP!!!

i personally prefer the p2k2 or monster stock depending on track layout.
Replies: 4
Views: 342
Posted By muahaha

RE: frankenstien motor quesion :)

with those 2 motor, i'll just keep them as they are. there much better way to extract powers.
Replies: 1
Views: 348
Posted By muahaha

RE: tc4 motor help

6t singles motor or a hacker brushless with 7 cells?
Replies: 9
Views: 434
Posted By muahaha

RE: servo

i set my servo setting as loose as possible (turn it all up the way until it hit the top brace and turn it back down a bit so there's a gap).
Replies: 12
Views: 1,262
Posted By muahaha

RE: Reedy krypton kr 10x2 motor trinity

revolution motors has a fatter torque band(more power across the rpm range). But i still reckon kr spool quicker then anything else (except for brushless of course).
Replies: 7
Views: 502
Posted By muahaha

RE: Red or Black ESC (13t or lower)

teiken g series - black colour
gm v series - black purple colour
ko vfs - black colour
Replies: 10
Views: 685
Posted By muahaha

RE: TC4 OR XXX-S

If given a choice, i'll pick tc4 over xxxs. Dun get me wrong, the xxxs is a good car, but it's also very old (shelf life) compare to the tc4 and since the tc4 is a newer car, much more can be done to...
Replies: 12
Views: 486
Posted By muahaha

RE: anti-roll bar?

Antiroll bars (aka sway bars or stabilizer bars) are wire like shaped rod (or how ever the maker of the car wants it to be) attach to either side of the arms acts as a secondary spring to the...
Replies: 25
Views: 1,679
Posted By muahaha

RE: TT-01 Any good for first car?

hmmm i wonder if u have ever try other motor/tires on the car.

the last time i ran a tt01 (stock 'cept for alu main, sport tune motor, bearings and some TO slicks) i am practical 2 laps down...
Replies: 9
Views: 467
Posted By muahaha

RE: Tuning Motors

get some teflon shims, some trinity xxx laydown brush, bushing oil and a hood alignment kit.

1. shim the armature so it's centered on the magnetic field. (use telfon shim on the side of the...
Replies: 29
Views: 1,413
Posted By muahaha

RE: power supply?

Personally i would not recommend u to use a computer power supply as they are rated not to be used outside a "casing" where casing refers to a computer case or other casing. Also a computer power...
Replies: 12
Views: 1,262
Posted By muahaha

RE: Reedy krypton kr 10x2 motor trinity

althou it has plenty of torque. the kr motor is one of the fastest spooling motor i have seen and i have seen plenty.
Replies: 9
Views: 434
Posted By muahaha

RE: servo

it depends on wat car u have. some car uses servo saver horns while other uses servo saver bellcranks. Tell us wats ur ride and someone here will be able to help u.
Replies: 8
Views: 386
Posted By muahaha

RE: Mr4TC Shocks

Just to get rid an assumption, not all touring car uses the same length shock.

now, in order to get the length u want, just unscrew the bottom end till u hit the length u want (which u have...
Replies: 15
Views: 576
Posted By muahaha

RE: How does a XXX-T brake ?

on the mc330, brake will not kick in until the car has totally stop. so even if u slam full brake it will not hit reverse. on the other hand mc330 does not offer any brake adjustment. so basically...
Replies: 11
Views: 404
Posted By muahaha

RE: returning fan

battery - bigger mah = more run time, match packs = more punch
motor - smaller number = faster motor = bigger ratio = quicker battery drainage
esc - limit on esc define how low a motor u can use...
Replies: 1
Views: 351
Posted By muahaha

RE: T4 rough track setup

the general ride height of a truck should be fornt arm level with chassis bumper and rear cvd should be level. depending on the ramp, normally i would coast (adjusting speed for needed height and...
Replies: 47
Views: 1,443
Posted By muahaha

RE: DO YOU THINK IT IS WORTH IT

hmmm let see,

golf (also a hobby sport)

clubs set - cost at least aus$1800 to get a good graphite shaft set
golf bag - $250
club membership - starts @ about aus$1200 and $600 for the...
Replies: 13
Views: 461
Posted By muahaha

RE: my frankensyein motor!

If u guys really wants a freakinstien motor u should try cobolt cans with epic armature and orion v2 endbells. I've tried it once just to see what it does. Huge torque band across the whole rpm range.
Replies: 42
Views: 1,319
Posted By muahaha

RE: Offical Picture thread **POST YOUR PICS**

I feel bad not sharing my rig with the members. so i pulled my truck out of the closet........
Replies: 25
Views: 825
Posted By muahaha

RE: need pro help (3PK or JRXS3)

helios my choice:D with the red grip and angled wheel extention, hell i think my brain will fart before my hand get uncomfortable.
Replies: 31
Views: 1,269
Posted By muahaha

RE: I need a good electric car...

Here's a list of the more popular ones

Tamiya
top model: trf415(belt), evo4(shaft),evo3 surikarn
intermediate: ta04r(belt), ta05(belt), tb02r(shaft)

Yokomo
top model: mr4tc BD (belt),...
Replies: 277
Views: 104,865
Posted By muahaha

RE: Mystery Solved! How to select the proper gearing for your electric RC!

Hi Skrap,

Thou Gray has dun nothing but butchered ur formulae to a million pieces, dun let him get the best of u. All ur sweat and effort has make gearing a much less hasle to most people. But...
Showing results 1 to 25 of 500
 


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service - Do Not Sell My Personal Information

Copyright 2018 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.