RCU Forums - Search Results

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Notices
 
Search: Posts Made By: Bobneal1
Showing results 1 to 25 of 231
Search took 0.82 seconds.
Forum: RC Jets
03-28-2020, 04:38 PM
Replies: 6
Views: 278
Posted By Bobneal1

Did you have telemetry logging turned on for...

Did you have telemetry logging turned on for those items? If not they will not be selectable.
Forum: RC Jets
02-02-2020, 06:54 AM
Replies: 29
Views: 1,901
Posted By Bobneal1

Shims

If you put thin plywood shims in the outboard retract mount holes and 1 in the forward inboard hole you can with some trial and error get the doors to close without toe out. Mine close after spending...
Forum: RC Jets
01-30-2020, 08:39 AM
Replies: 249
Views: 53,593
Posted By Bobneal1

It very easy, One 3mm cap bolt that is captured...

It very easy, One 3mm cap bolt that is captured in the vertical fin and disconnect the servo cable and you are done. It takes a minute or two at the most.


Bob Neal
Forum: RC Jets
01-23-2020, 02:34 PM
Replies: 29
Views: 1,901
Posted By Bobneal1

You have to shim the retract units on the wing...

You have to shim the retract units on the wing mounting rails.
Forum: RC Jets
01-23-2020, 08:12 AM
Replies: 1
Views: 177
Posted By Bobneal1

JR Xbus servo programmer

Anybody ever use one of these? I'm looking to change the resolution of 8911 brush less servos to smooth them out.
Forum: RC Jets
12-25-2019, 09:20 AM
Replies: 1,572
Views: 175,774
Posted By Bobneal1

Just a suggestion, How about posting your...

Just a suggestion,

How about posting your starting basic jet file here , Then people could download it and modify as necessary for their individual tastes.
Forum: RC Jets
12-24-2019, 08:32 AM
Replies: 4
Views: 712
Posted By Bobneal1

Dreamworks Bob Neal

Dreamworks


Bob Neal
Forum: RC Jets
11-28-2019, 08:57 PM
Replies: 13
Views: 1,954
Posted By Bobneal1

Talk to Dee Force RC. I spoke with the tech a few...

Talk to Dee Force RC. I spoke with the tech a few months ago and he said he could work on 12X JR radios.
Forum: RC Jets
10-30-2019, 11:18 AM
Replies: 41
Views: 8,060
Posted By Bobneal1

Dreamworks services Jetcats

Dreamworks services Jetcats
Forum: RC Jets
10-14-2019, 05:27 PM
Replies: 193
Views: 24,254
Posted By Bobneal1

+1

+1
Forum: RC Jets
10-05-2019, 06:21 PM
Replies: 35
Views: 2,032
Posted By Bobneal1

Parking

Jamie,

We will need 4 I think.

Thanks

Bob Neal
Forum: RC Jets
10-04-2019, 05:11 PM
Replies: 35
Views: 2,032
Posted By Bobneal1

Tiger Meet parking

Jamie,

I need a parking spot . Iíll be with Bob Klenke . Nir Schweitzer and Dave Fepelstein
are going to be in the same area as well.

Thanks,

Bob Neal
Forum: RC Jets
09-04-2019, 06:19 AM
Replies: 17
Views: 925
Posted By Bobneal1

Dee Force Aviation sells JR 8411's and they have...

Dee Force Aviation sells JR 8411's and they have HV versions of them as well.

Just FYI.


Bob Neal
Forum: RC Jets
08-28-2019, 09:43 AM
Replies: 7
Views: 597
Posted By Bobneal1

You can do it yourself. I didn't have the powder...

You can do it yourself. I didn't have the powder coating equipment, it costs about $60 from Harbor freight. Then you have to buy the powder about 20$. Then you have to have an old oven, I did not. A...
Forum: RC Jets
08-28-2019, 05:57 AM
Replies: 7
Views: 597
Posted By Bobneal1

Landing gear

If you really want it nice, Take it apart and take it to a powder coating service. I got mine done for a little over $100. Its ten times tougher than paint and it looks awesome.

Bob Neal
Forum: RC Jets
07-21-2019, 10:52 AM
Replies: 1,572
Views: 175,774
Posted By Bobneal1

Auto gear down

I had mine set up to extend the gear below 60 psi. Worked great but, if you lose the telemetry link for just a moment , your gear will come down and when you get the link back it goes back up. This...
Forum: RC Jets
06-30-2019, 05:26 AM
Replies: 25
Views: 1,219
Posted By Bobneal1

It would be easy to add a simple timing circuit...

It would be easy to add a simple timing circuit that would require a specific amount on the “ground “ time before triggering, thereby eliminating the bounce issue.. I can see a situation where a...
Forum: RC Jets
06-29-2019, 04:55 PM
Replies: 25
Views: 1,219
Posted By Bobneal1

How about a squat switch on the main gear. Then...

How about a squat switch on the main gear. Then you could use it on takeoff (aborted) or landing or whatever.


Bob Neal
Forum: RC Jets
06-28-2019, 01:39 PM
Replies: 14
Views: 1,001
Posted By Bobneal1

Altecare in Canada sells a setup for servo...

Altecare in Canada sells a setup for servo operated ball valve.

altecarerc.com I believe.

Bob Neal
Forum: RC Jets
06-20-2019, 04:15 AM
Replies: 114
Views: 9,840
Posted By Bobneal1

Clogged injector

You could try compressed air and see if you can blow out the restriction.


Bob Neal
Forum: RC Jets
06-09-2019, 10:12 AM
Replies: 4
Views: 387
Posted By Bobneal1

The difference was amazing on my Skygate hawk....

The difference was amazing on my Skygate hawk. The gear would take 8+ seconds with the standard valve and take only about one second with the high flow valve.


Bob Neal
Forum: RC Jets
06-03-2019, 11:35 AM
Replies: 1,572
Views: 175,774
Posted By Bobneal1

Wayne, Thanks for your insights. I spoke...

Wayne,

Thanks for your insights. I spoke with James at Esprit and he said the servo doesn't like being driven that far. It's -150 % I tried a JR brushless WV servo and it works fine. I'll replace...
Forum: RC Jets
06-03-2019, 04:21 AM
Replies: 1,572
Views: 175,774
Posted By Bobneal1

Yeah, maybe I do have a setting off ,but , I...

Yeah, maybe I do have a setting off ,but , I plugged in a different servo, a JR brushless WV servo and it works fiine. So I doubt it.

I keep having compatibility issues with ancillary items like...
Forum: RC Jets
06-01-2019, 01:23 PM
Replies: 1,572
Views: 175,774
Posted By Bobneal1

Sequencer

Thr weird part is it was working perfectly and then it started doing this. Iím going to plug another servo into that rx port and see what happens
Forum: RC Jets
06-01-2019, 10:47 AM
Replies: 1,572
Views: 175,774
Posted By Bobneal1

Sequencer help

I have a gear door servo thatís acting weird. Itís the second door track on the sequencer. The servo drives as it should with the sequencer but it seems to switch off. You can take your hand and...
Showing results 1 to 25 of 231
 


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service - Do Not Sell My Personal Information

Copyright © 2018 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.