RCU Forums - Search Results

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Notices
 
Search: Posts Made By: bgold
Showing results 1 to 25 of 407
Search took 0.73 seconds.
09-30-2010, 12:47 AM
Replies: 4
Views: 1,377
Posted By bgold

RE: MEJZLIK AND PT MODELS CF 3 BLADE PROPS ???

I just got a 28.5 x 12s 3 blade from Chief the middle of September.
09-09-2010, 01:45 AM
Replies: 1
Views: 790
Posted By bgold

41% Extra

Just did the maiden on a 41% Extra that has been hanging around for a couple of years. Tom this is a great flying airplane. This is the second one I've had and guys today could see me flying better...
06-30-2010, 12:11 AM
Replies: 48
Views: 4,473
Posted By bgold

RE: Pull pull question

You have to do 2 things to get rid of the slack.
1. Get the pivot point of the control horn on the hinge line exactly, not just close.
2. Make sure the servo arm is the same size as the distance...
06-05-2010, 12:45 AM
Replies: 8
Views: 1,242
Posted By bgold

RE: how would you ship a giant plane like a 46% 110

I have shipped a couple of times by Forward Air, $150 Omaha to Portland and $170 Louisiana to Portland. No problems.
05-16-2010, 11:30 PM
Replies: 11
Views: 1,471
Posted By bgold

RE: thrust anglepic

The fire wall should be 2 or 3 degrees of right thrust and that's why the cross hare is off center with the circle. If you center the mounting bolts on the cross hare then the right thrust of the...
03-22-2010, 08:18 AM
Replies: 6
Views: 5,440
Posted By bgold

RE: Hinges for removable rudder for 40% plane

I did all that with Robart hinges and at best it's very difficult to get the rudder back on. My new TT TOC plane came with hinges installed and ready for the removable rudder. They used oversized...
03-03-2010, 11:09 PM
Replies: 20
Views: 1,906
Posted By bgold

RE: Any Station Wagon owners out there

I do know for a fact that 41 & 42 percent Extras will fit inside the back of 2007 -2010 Ford Expedition EL as in extended length and both front seat people are comfortable.
02-24-2010, 12:47 AM
Replies: 21
Views: 1,693
Posted By bgold

RE: When should you stop using battery packs with a standard connector?

Question is still about connectors and the JR plugs wont handle a high discharge NiMh current.
02-24-2010, 12:44 AM
Replies: 19
Views: 1,547
Posted By bgold

RE: PLEASE HELP (Lithium Ion Batteries)

Don't be cheap, replace them with new Fromeco 2600's and if you are using JR type plugs from your regulator get 2 outputs from each regulator and plug into your receiver and operate worry free except...
02-22-2010, 11:27 PM
Replies: 19
Views: 1,547
Posted By bgold

RE: PLEASE HELP (Lithium Ion Batteries)

What brand are they, Fromeco hasn't made a 2400 pack for over 3 years
02-22-2010, 11:22 PM
Replies: 21
Views: 1,693
Posted By bgold

RE: When should you stop using battery packs with a standard connector?

Those connectors are rated for 4 amps, each one of your 8 servos can draw as much as 4 amps. Use higher capacity connectors if you have the high powered servos. I use 30 amp Anderson power poles,...
02-08-2010, 01:34 AM
Replies: 6
Views: 1,306
Posted By bgold

RE: Looking for Good Throttle Servo

Use what ever servo you think is good enough for your ailerons, elevators or rudder. It will also be good enough for you throttle. I use the throttle as much as I do any other control so why would...
12-08-2009, 05:10 AM
Replies: 4
Views: 1,085
Posted By bgold

RE: TT TOC elevator servo mounting?

I use socket head servo screws and use a 5/64 bit with a long extension to reach in and install the servo screws. The hard part is getting the servo in place. Cut the covering away from the slot. ...
09-21-2009, 12:28 AM
Replies: 6
Views: 727
Posted By bgold

RE: Dual Lipo problem

Get a Fromeco Wolverine switch and cure your problems
08-24-2009, 02:14 AM
Replies: 2
Views: 312
Posted By bgold

RE: 41% Extra in classifieds

Tobe, Please call me @503-351-2036 to make arranegements. I'm in the Pacific time zone so I'm a couple of hours behind you
Thanks
Bill
08-15-2009, 11:20 PM
Replies: 18
Views: 1,979
Posted By bgold

RE: Pull pull help needed

What will keep your cables tighter than any thing is to have the pivot point of the control horn connection right on the hinge line and then use a servo arm that will have exactly the same width as...
08-09-2009, 11:05 PM
Replies: 47
Views: 4,326
Posted By bgold

RE: 41% extra

Sorry to hear that Tom. I would have got another one in a heartbeat if they were available. Best plane I've ever flown.
07-27-2009, 08:36 AM
Replies: 6
Views: 771
Posted By bgold

RE: Expert Advice Needed

Next time glue some wood over the end of the sleeve to seal it better. Heat the tube to get the epoxy to release.
07-23-2009, 10:41 PM
Replies: 11
Views: 1,183
Posted By bgold

RE: Dave Brown vs Tru Turn

I've use the 5" with a lightened backplate on a DA-150, the spinner is great and way cheaper. I've got a three blade on the way.
07-08-2009, 08:27 AM
Replies: 17
Views: 2,931
Posted By bgold

06-04-2009, 12:09 AM
Replies: 44
Views: 3,793
Posted By bgold

RE: spinner balancing

To dynamic balance you need to be able to work in multiple planes (not airplanes) and balance to a rpm you have selceted that is best for your part and your balancer is capeable of running at.  Don't...
05-07-2009, 11:16 PM
Replies: 16
Views: 1,662
Posted By bgold

RE: Graphics

Kirbys, quality and fast with a huge library of graphics
04-21-2009, 03:46 AM
Replies: 47
Views: 4,326
Posted By bgold

RE: 41% extra

This past weekend was the Polar Bear IMAC here in the North West, my first try in Sportsman. The WH had 16 flights before the contest. I finished 5th out of 11 in Sportsman and won the Seniors. ...
04-16-2009, 12:48 AM
Replies: 47
Views: 4,326
Posted By bgold

RE: 41% extra

Exactly what is the proper method of bolting the landing gear in place.
Showing results 1 to 25 of 407
 


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service - Do Not Sell My Personal Information -

Copyright 2021 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.