RCU Forums - Search Results

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Notices
 
Search: Posts Made By: xt2nitro
Showing results 1 to 25 of 99
Search took 0.34 seconds.
05-10-2009, 04:17 AM
Replies: 21
Views: 1,958
Posted By xt2nitro

RE: The Guy in the Model Shop Was Shocked!

I am getting a newone way bearing. Hopefully this should sort the issues.
05-07-2009, 10:32 AM
Replies: 21
Views: 1,958
Posted By xt2nitro

RE: The Guy in the Model Shop Was Shocked!

How do you know if the one way bearing has gone? I think that's whats causing the starter to spin over. I tried cleaning the bearing with fuel and putting it back in and it just did the same thing....
05-06-2009, 10:27 AM
Replies: 11
Views: 1,579
Posted By xt2nitro

RE: Cleaning your rc

Can't you use water to clean the chassis?
05-02-2009, 02:00 PM
Replies: 21
Views: 1,958
Posted By xt2nitro

RE: The Guy in the Model Shop Was Shocked!

I picked my engine up today after it had been fixed. I fitted the engine back onto the chassis expecting the car to work. I started the car and it ran for about 5 seconds and stopped working again....
04-27-2009, 01:32 PM
Replies: 21
Views: 1,958
Posted By xt2nitro

RE: The Guy in the Model Shop Was Shocked!

After getting back from holiday there is still no sign of my nitro machine been returned to me! I am sick of waiting...
04-27-2009, 01:24 PM
Replies: 10
Views: 1,326
Posted By xt2nitro

RE: What should I get Losi XXL or 8ight-t 2.0 rtr?

Why does everybody always go for the "T" version and not just the buggy version?
04-27-2009, 01:21 PM
Replies: 8
Views: 4,595
Posted By xt2nitro

RE: Newbie just ordered a BIY ACME Condor kit

Good luck with that thing....
04-11-2009, 03:54 AM
Replies: 21
Views: 1,958
Posted By xt2nitro

RE: The Guy in the Model Shop Was Shocked!

I am going on holiday to the Carribean... My engine has been sent back to Ripmax/Global for free repairs, and is due back hopefully before I get back. At least when the holiday is over I can look...
04-09-2009, 04:21 PM
Replies: 21
Views: 1,958
Posted By xt2nitro

RE: The Guy in the Model Shop Was Shocked!

Ripmax is a company within Europe that distributes XTM products, whereas in America the company that distributes XTM products are under the name of Global Hobbies.
04-09-2009, 02:18 AM
Replies: 21
Views: 1,958
Posted By xt2nitro

RE: The Guy in the Model Shop Was Shocked!

The porting for the exaust was facing in the engine so there was only a little gap for smoke to escape.
04-08-2009, 10:35 AM
Replies: 21
Views: 1,958
Posted By xt2nitro

RE: The Guy in the Model Shop Was Shocked!

My engine is still in the store, and the shop owner has the pics. I will post pics if I can get the them sometime soon. Yes the pison/sleeve and clutch shoes were fitted wrong after warenty repairs...
04-08-2009, 10:23 AM
Replies: 21
Views: 1,958
Posted By xt2nitro

The Guy in the Model Shop Was Shocked!

So I took my XTM XT2 to my local model shop for inspection because I thought my electric starter was not working, and I had been trying hours trying to find the cause. The guy removed the starter...
04-05-2009, 02:18 PM
Replies: 3
Views: 667
Posted By xt2nitro

RE: What has happened?

No I don't think so, but I don't know for sure. The instructions are at: http://media.hobbypeople.net/manual/145625.pdf ...Go to page 45... Thanks.
04-05-2009, 06:01 AM
Replies: 3
Views: 667
Posted By xt2nitro

RE: What has happened?

My engine does turn over via the fly wheel. I was just not pushing on it hard enough. Does anyone know which order all the nuts etc assemble to get the clutch bell spinning properly?
04-05-2009, 05:49 AM
Replies: 3
Views: 667
Posted By xt2nitro

What has happened?

Hi everyone,

My engine was not starting so I did a check for air leaks, and I discovered that my carb was not completely sitting in the crankcase. So I loosened the pinch bolt and pushed it back...
04-01-2009, 04:24 PM
Replies: 2
Views: 705
Posted By xt2nitro

RE: cirrus radios

I use a Cirrus radio and I have had no problems so far. I believe Cirrus works well with futaba gear, so you should be OK with a Futaba RXS alongside the Cirrus radio as long as they are on same...
04-01-2009, 12:03 PM
Replies: 8
Views: 1,488
Posted By xt2nitro

RE: glow plug life

I always check my glow plug at the end of each run. I do notice the very tip of the silver coil in the glow plug is black. My plug is only new! Is this normal?
03-26-2009, 03:58 PM
Replies: 22
Views: 1,856
Posted By xt2nitro

RE: My hobby shop story!

I first got into models when I purchased a Firebird XL airplane from my LHS which is about 5 minutes away. I loved the thing, however I crashed it loads. Each time I crashed it they patched it for...
03-23-2009, 05:16 PM
Replies: 14
Views: 2,084
Posted By xt2nitro

RE: Tower Terror keeps burning up glow plugs, and wont run consistent for a whole tank

My XTM 24.7 did this and then the con rod eventually broken. After the con rod was replaced I richened the HSN half a turn and replaced the glow plug and it seemed fine.
03-21-2009, 06:13 PM
Replies: 8
Views: 796
Posted By xt2nitro

RE: A Tank of Fuel! How long?

Thanks for the answers... I just needed to know that I was roughly on the right track with 7 minutes for lots of WOT.
03-21-2009, 06:06 PM
Replies: 8
Views: 796
Posted By xt2nitro

RE: A Tank of Fuel! How long?

I thought more fuel enters the engine at low speeds because there is not so much air getting in and at high speeds less fuel enters the engine because more air is getting in which is what speeds up...
03-21-2009, 11:12 AM
Replies: 8
Views: 796
Posted By xt2nitro

A Tank of Fuel! How long?

Hi,
I was running my XT2 like crazy today with loads of WOT on a huge field (the car hardly had a break)... My 125cc fuel tank filled right to the top lasted only 7 minutes! Is this normal or does...
03-18-2009, 04:17 PM
Replies: 1
Views: 559
Posted By xt2nitro

Schumacher Rascal

Hi,
Over the next few days I will be helping my freind get is brand new Schumacher Rascal up and running and tuned. Have you ever had one of these? Do you know anything that is common to be a...
03-18-2009, 04:08 PM
Replies: 12
Views: 1,273
Posted By xt2nitro

RE: high idle needed to keep running

Yes the engine would be running rich if fuel is spitting from the exaust however this is normal for new engines. Set the low speed needle back to stock and then start tuning it to suit your needs.
03-18-2009, 03:43 PM
Replies: 12
Views: 1,273
Posted By xt2nitro

RE: high idle needed to keep running

I noticed in another post you said "fuel was spitting from the tank". Do you mean fuel is leaking out from the fuel tank?
Showing results 1 to 25 of 99
 


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service - Do Not Sell My Personal Information -

Copyright 2021 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.