RCU Forums - Search Results

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Notices
Search: Posts Made By: va3mw
Showing results 1 to 15 of 15
Search took 0.28 seconds.
08-07-2009, 08:45 PM
Replies: 3
Views: 889
Posted By va3mw

RE: multi-prop and more on a 12FG

One more question not that I have had a chance to play with this.

When you have one engine on ch 3 and the other on ch 6 say. I can set up the end points for each channel without any issues.
...
06-12-2009, 06:20 PM
Replies: 3
Views: 889
Posted By va3mw

RE: multi-prop and more on a 12FG

Thanks Bill for the awesome support.  I will give it a try.
06-12-2009, 06:43 AM
Replies: 3
Views: 889
Posted By va3mw

multi-prop and more on a 12FG

I'm pretty new to mixing, groups and the advanced features of a 12FG (or just about any other receiver).

I got a plane that I'm setting up with 2 aileron channels and twin engines. So this is a 2...
04-27-2009, 06:41 PM
Replies: 5
Views: 4,369
Posted By va3mw

RE: Want to buy Draganflyer Ti V

now, that was a helpful post.
04-19-2009, 08:53 PM
Replies: 5
Views: 4,369
Posted By va3mw

RE: Want to buy Draganflyer Ti V

I have one to sell if you like. It is new and zero flight time on it (other than a test flight).

I have have a ton of propellers/parts/motors, the shipping/storage case, 2 batteries, receiver,...
01-19-2009, 12:58 AM
Replies: 2
Views: 2,691
Posted By va3mw

RE: Draganflyer V Ti Max Current draw

What type of battery are you using? What is the amp hour rating?

Mike
12-10-2008, 12:24 AM
Replies: 3
Views: 1,718
Posted By va3mw

RE: Motor Not Spinning Up - Newbie

They usually test fly them before they ship them. Are all your trims set to center (except throttle)?

Make sure the connector on the bottom of the board is fully connected.

As for the...
11-14-2008, 11:55 PM
Replies: 3
Views: 1,968
Posted By va3mw

RE: NEW MAIN ROTOR BLADES

So, how did they fly? Where did you find the blades? They look great!
11-14-2008, 11:50 PM
Replies: 0
Views: 1,398
Posted By va3mw

TI-V update and what I've learned so far

I've been playing around with my TI-V since September. Between practice flights and practicing with the helicopters on Realflight G4, I've gotten a lot more comfortable with it. I now also have 2...
10-10-2008, 08:16 PM
Replies: 6
Views: 1,787
Posted By va3mw

RE: Electronics help

As long as the caps are 0.01uF and greater than 12VDC (which is the maximum service voltage), your good to go.
10-10-2008, 08:12 PM
Replies: 3
Views: 1,547
Posted By va3mw

RE: capacitor type? novice question.

The 12V is the maximum rating that the capacitor can work with. So, as long as it is higher than 12V, that is fine. Now, if you put a 6V cap on it, you get to see what happens when capacitors...
10-10-2008, 01:32 PM
Replies: 16
Views: 4,419
Posted By va3mw

RE: IV Ti has gone bonkers

I'm chasing a similar problem with mine. The right motor seems to start faster than all the rest and with more power.

If you can solder, make sure you don't have any cold solder joints in the 4...
09-08-2008, 02:05 PM
Replies: 2
Views: 1,182
Posted By va3mw

RE: New TI-V owner

The one that came with the TI-V. FMS 2.0.
09-08-2008, 01:32 PM
Replies: 2
Views: 1,182
Posted By va3mw

New TI-V owner

So... where to start. I've lots of what is here and I'm hoping that someone can take a few minutes as a checkpoint and recommend what to do next.

I've:

spent about 10 hours on the...
09-08-2008, 09:07 AM
Replies: 71
Views: 15,163
Posted By va3mw

RE: What The.... Noooooooo!

I'm pretty new to the DF front, but just received my TI-V a few weeks back. Like old man mike, I've been a Ham for a very long time and clearly understand RF issues.

On the weekend, I was...
Showing results 1 to 15 of 15


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service - Do Not Sell My Personal Information -

Copyright 2021 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.