Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Notices
 
Search: Posts Made By: Kimhoff
Showing results 1 to 25 of 500
Search took 0.94 seconds.
Forum: Marketplace
09-25-2018, 10:07 AM
Replies: 12
Views: 593
Posted By Kimhoff

Servos

stiil have these?
05-17-2014, 05:03 PM
Replies: 1
Views: 483
Posted By Kimhoff

DYI Voltage Regulator

Does anyone have a goode DYI voltage reg thst will handle 7.4 volts in and output 6 or 5 volts? If so can you share the schmatic and parts list?

I can buy the MPI for $20 but I like to built...
Forum: Gas Engines
03-04-2014, 06:53 PM
Replies: 62
Views: 8,428
Posted By Kimhoff

Can someone explain the process for truing the...

Can someone explain the process for truing the reedblock?
Forum: Glow Engines
01-27-2013, 11:00 AM
Replies: 28
Views: 6,383
Posted By Kimhoff

RE: FF-320 Rebuild

Just wanted to post the connecting rod bolt part number for future reference.

41820001
Forum: Gas Engines
11-14-2012, 04:44 PM
Replies: 34
Views: 10,750
Posted By Kimhoff

RE: maloney engine???

Convert it to battery ignition and lose a pound of weight. Pull the flywhel and the back case extention. You can use a standard rail mount to mount it. Starting will be easy.
Forum: Gas Engines
11-14-2012, 04:40 PM
Replies: 10
Views: 856
Posted By Kimhoff

RE: Fuji troubles contine

Low end it too lean.
10-16-2012, 02:47 PM
Replies: 8
Views: 1,637
Posted By Kimhoff

RE: How to loosen hinges

Ever think of putting a little earl on them?
Forum: Gas Engines
08-26-2012, 08:00 AM
Replies: 20
Views: 1,751
Posted By Kimhoff

RE: SV 50cc

If you are setting it with the pencil method the magnet wil pass the pickup by 3/8 of and inch.
Forum: Glow Engines
08-25-2012, 12:54 PM
Forum: Glow Engines
08-06-2012, 05:37 PM
Replies: 9
Views: 995
Posted By Kimhoff

RE: Magnum 120FS RPM issue

Some Magnums time at 6 o'clock while other time at 5:30.  Best way to check is overlap at TDC on the exhuast stroke.
Forum: Gas Engines
07-30-2012, 04:53 PM
Replies: 6
Views: 1,013
Posted By Kimhoff

RE: GT33 quits running.

Check the reed leafs and make sure they are sealing.
Forum: Glow Engines
07-29-2012, 03:22 PM
Replies: 59
Views: 4,581
Posted By Kimhoff

RE: glow plug thread

I would say someone had a DA moment.
Forum: Glow Engines
07-29-2012, 03:21 PM
Replies: 20
Views: 2,715
Posted By Kimhoff

RE: Magnum Carb on OS 70 FS-1

Why are you concerned about smoke?  You should concentrate on getting the needles set correctly.
07-10-2012, 05:12 PM
Forum: Glow Engines
06-09-2012, 11:19 AM
Replies: 12
Views: 1,414
Posted By Kimhoff

RE: Ring cooked unto piston

Put it in the oven at 300 degrees for 20 minutes and it will come right out.</p>
Forum: Glow Engines
05-01-2012, 05:02 PM
Replies: 4
Views: 838
Posted By Kimhoff

RE: Saito Bearing replacement -

If the link worked.
Forum: Glow Engines
04-29-2012, 10:54 AM
Replies: 17
Views: 3,003
Posted By Kimhoff

RE: New-to-me SuperTigre 3000

Stay thursty my friend!
Forum: Glow Engines
04-25-2012, 03:33 PM
Replies: 90
Views: 21,991
Posted By Kimhoff

RE: Super Tartan Twin 77

Should work.  Sounds like you carb has issues it the HSN is not haveing any affect.  Have you rebuilt it?  Can you post pic of the EI setup?   Specifially the pickup hall IC.
Forum: Glow Engines
04-25-2012, 03:25 PM
Replies: 90
Views: 21,991
Posted By Kimhoff

RE: Super Tartan Twin 77

You need to put a Dl 30 reed block on there.  Are you running gas or meth?
Forum: Glow Engines
04-25-2012, 02:58 PM
Replies: 90
Views: 21,991
Posted By Kimhoff

RE: Super Tartan Twin 77

what did you set your timing at?  Sound rich to me. Some pics of the EI setup would be nice.
Forum: AutoGyros
04-12-2012, 08:05 AM
Replies: 2
Views: 1,578
Posted By Kimhoff

Forum: Gas Engines
03-24-2012, 06:19 PM
Replies: 10
Views: 1,392
Posted By Kimhoff

RE: High Idle Speeds

There is a primary driver to the idle ability of the Bully (or any older engne) and the new engines being made. It is called weight.
03-20-2012, 04:45 PM
Replies: 10
Views: 1,364
Posted By Kimhoff

RE: HK CS question about JR 10X conversion to 2.4

It will work but if I were you I would look at the Hitec JR module.
Forum: Glow Engines
03-20-2012, 04:34 PM
Replies: 11
Views: 1,084
Posted By Kimhoff

RE: Saito parts

<p class="MsoNormal" style="MARGIN: 0in 0in 0pt"><font face="Times New Roman" size="3">Have you guys heard about the Earthquake and Tsunami they had in...
Forum: Glow Engines
03-19-2012, 04:02 PM
Replies: 90
Views: 21,991
Posted By Kimhoff

RE: Super Tartan Twin 77

Not sure why you think you need a different prop hub?  The DL 30 reed block is a nice upgrade.  Tower Hobbies has it for $15.  You will need to make an adapter plate out of flat aluminum.  It is...
Showing results 1 to 25 of 500
 


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service - Do Not Sell My Personal Information -

Copyright 2018 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.