Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Notices
Search: Posts Made By: redjet
Showing results 1 to 16 of 16
Search took 21.02 seconds.
Replies: 51
Views: 4,870
Posted By redjet

RE: AIRTRONICS 2.4GHz A GOOD DEAL?

You might want to check the exchange rate for US dollar to Pounds. $229 = 157.166 British Pounds
01-15-2009, 02:20 PM
Replies: 2,617
Views: 329,412
Posted By redjet

RE: *Airtronics RD8000 2.4 GHz*

Thanks for all of the feedback on the Rx voltage.
01-15-2009, 02:35 AM
Replies: 2,617
Views: 329,412
Posted By redjet

RE: *Airtronics RD8000 2.4 GHz*

Why are some folks running the 2.4 receivers with 6 volts. I have read that Spektrum had problems with receivers dropping out because of the battery packs premature voltage loss, but Airtronics has...
Forum: ARF or RTF
02-05-2008, 02:25 AM
Replies: 9
Views: 969
Posted By redjet

RE: Hinges ca or not to ca..

I get a very bad physical reaction to CA glues and have had to fine another source to glue CA hinges. Consequently, I have been using the Radio South 1/4 scale hinges and gluing them in place with...
Replies: 6
Views: 866
Posted By redjet

RE: HITEC 635HB SERVOS

To be sure you haven't inadvertently programmed something into the 9C to create the problem, try putting the 9C in servo mode and check the servo operation.
12-17-2005, 01:19 AM
Replies: 2
Views: 840
Posted By redjet

RE: Ultra Stick/Futaba 9C Problem

I suggest you go to FAQ #40 and follow the instructions. Forget about PMIX 4 & 5. All of the rest should setup ok.
12-17-2005, 01:03 AM
Replies: 3
Views: 568
Posted By redjet

RE: 9C trim graduations

Enter into the TRIM mode. The default for each item in TRIM is 4. Just use the down button and go to Throttle and rotate dial down to 1 which is as fine as you can get for TRIM.

Actually, I...
12-03-2005, 02:09 AM
Replies: 4
Views: 707
Posted By redjet

RE: 9C - changing slider reference

Bill,

Thank you for the help, but you suggest a complete new setup that is different from the FAQ version for quad flaps. I really didn't want to redo the entire program - all I was requesting...
11-29-2005, 11:44 PM
Replies: 4
Views: 707
Posted By redjet

9C - changing slider reference

I have an Ultra stick 60 - Quad flaps and a 9C Super radio. Being a newbie with the radio, I was able to setup the crow and continuous ailerons (as outlined in the FAQ #40). It took a lot of trial...
Replies: 0
Views: 283
Posted By redjet

Moving Slider Zero Reference

I have an Ultra stick 60 - Quad flaps and a 9C Super radio. Being a newbie with the radio, I was still able to setup the crow and continuous ailerons (as outlined in the FAQ #40). It took a lot of...
Replies: 7
Views: 761
Posted By redjet

RE: Choosing Servos

If your interested in doing some math - this site may be for you.

http://www.csd.net/~cgadd/eflight/calcs_servo.htm
05-16-2005, 06:35 PM
Replies: 3
Views: 454
Posted By redjet

RE: Futaba 9C Synthesized

Thanks for the quick response
05-15-2005, 10:35 PM
Replies: 3
Views: 454
Posted By redjet

Futaba 9C Synthesized

It is reported that the 9C synthesized Tx will work fine with Futaba RXs but may not with other compatible brand RXs. What does the synthesizer change in the TX that makes operation with other brand...
Forum: Beginners
04-25-2005, 10:14 PM
Replies: 11
Views: 922
Posted By redjet

RE: landing gear problems with NEXstar

If the landing struts are not holding in place, you can access the lock pins between the servos. You will need a bright light like the sun to see them. Tilt the fuselage around until you see the...
Forum: Beginners
03-23-2005, 12:46 AM
Replies: 38
Views: 2,519
Posted By redjet

RE: i crashed the nexstar

I assume the NEXstar was purchased more than 60 days prior to your unfortunate mishap. If within 60 days of purchase, and you have not soloed - Hobbico will replace the broken NEXstar. Read the...
Forum: Beginners
03-23-2005, 12:18 AM
Replies: 12
Views: 1,609
Posted By redjet

RE: 4 modeltronics hobby traders

I also purchased a Saito 100 from him and waited a couple of weeks for delivery because he was at a show. I contacted him through EBay and he phoned me to make sure I got the engine. Would...
Showing results 1 to 16 of 16


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service - Do Not Sell My Personal Information -

Copyright 2018 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.