RCU Forums - Search Results

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Notices
Search: Posts Made By: 6topham9
Showing results 1 to 22 of 22
Search took 0.19 seconds.
05-12-2010, 10:50 PM
Replies: 3
Views: 410
Posted By 6topham9

RE: NEED HELP

thinking itis a spur gear?? the big one apparently had been upgraded to a steel one...the smaller one that it meshes with all of a sudden looks chewed up on the side closer to the big gear.. sorry no...
05-12-2010, 07:16 PM
Replies: 3
Views: 410
Posted By 6topham9

NEED HELP

anyone in toronto area?
my savage needs help.... techincal terms are at a loss. Ihave a new servo for forward and reverse. they USED to work. Now it seems like a gear thingy is stripping on one...
05-12-2010, 07:03 PM
Replies: 12
Views: 1,134
Posted By 6topham9

RE: battery level indicator

mmm i think its less than that. I have the level meter, trust me, its no a hinderence. If you batteries are that low, you should change em anyways!LED'S wont drain anything! its a convienience.
05-12-2010, 08:21 AM
Replies: 12
Views: 1,134
Posted By 6topham9

RE: battery level indicator

i have one, its indestructible as with most bits... also great since it takes the guess-work out of knowing levels. nothing like having the car pass by you, then 5 seconds later off in no mans land...
05-12-2010, 01:55 AM
Replies: 11
Views: 3,002
Posted By 6topham9

RE: savage sway bar

there has to be predrilled holes in the arms  from about half way down
05-11-2010, 06:14 PM
Replies: 4
Views: 727
Posted By 6topham9

RE: carb leaking??

sorry, meant the high speed needle... and mid range needle..... axial 32</p>
05-11-2010, 03:39 PM
Replies: 4
Views: 727
Posted By 6topham9

carb leaking??

so i dont know what caused this, but i saw fuel come out of the low speed needle... did i prime it too much? could the needle be turned out too much? i didnt have time to check as somehow i rolled...
05-11-2010, 11:35 AM
Replies: 11
Views: 3,002
Posted By 6topham9

RE: savage sway bar

i know this is an old posting, however, Im installing them as we speak... boy what a pain! of course a casted hand doesnt help! but the difference will be worth it!!!

  clean, clean, clean the...
05-09-2010, 08:34 PM
Replies: 14
Views: 868
Posted By 6topham9

RE: drivetrain help

yea I think the pipe is a bit of an issue. Any recommendations? The one on it is the HPI ribbed one.. apparently its not that good ( i bought this thing used).
05-06-2010, 08:34 AM
Replies: 14
Views: 868
Posted By 6topham9

RE: drivetrain help

it smokes, just seems to SCREAM!!! everyone talks about wheelies and this wont come close to it (which I dont mind). I believe the engine is the axial 32 spec 1 that the guy put in it and it has the...
05-05-2010, 06:10 PM
Replies: 9
Views: 1,069
Posted By 6topham9

changing charging polarity

I posted somewhere else on this forum, cant remember where.. the new spektrum i have is negative centre on the charging pole. The charger Ihave now is positive centre.. obviously they cant work...
05-05-2010, 05:37 PM
Replies: 2
Views: 799
Posted By 6topham9

Spektrum issue?!?!?

So I just upgraded to the spektrum dx3e.. great price and liked the dials instead of digital screen. My question is this:
Charging wit it says it is negative centre. I have a charger that charges...
05-05-2010, 02:09 PM
Replies: 14
Views: 868
Posted By 6topham9

RE: drivetrain help

alrighty!!! its back!! shifting needs a little help still, but 4 wheel drive is back...I have to tune the rich/ lean on the high speed i think... possibly the low and idle speed too.... I wish there...
05-03-2010, 05:17 PM
Replies: 14
Views: 868
Posted By 6topham9

RE: drivetrain help

didnt matter... it would just not change, you could tell it needed another gear.... it would just take long.. or not at all.


it was working 2 weeks ago, then a few things happened, and now it...
05-03-2010, 01:24 PM
Replies: 14
Views: 868
Posted By 6topham9

RE: drivetrain help

thank yo very much!! I ws spinning and spinning and I thought the screw fell out... thank you for the tips!!! hopefully it works! I turned it out a little,, the screw felt like it was allll the way...
05-03-2010, 11:51 AM
Replies: 14
Views: 868
Posted By 6topham9

RE: drivetrain help

wel after i took out the rear diff... i saw it was a set screw in between the center tranny and the brakes.. it had fallen out... havent run it yet, but we shall see,, what a freakin pain... 2 horus...
05-02-2010, 08:24 PM
Replies: 14
Views: 868
Posted By 6topham9

drivetrain help

So i was driving my savage and the rear tires were dragging. the fronts were spinning like crazy to pull the car, but i put on brakes and the rears lock up..
where do I even start to investigate the...
04-30-2010, 10:17 PM
Replies: 6,159
Views: 703,274
Posted By 6topham9

04-29-2010, 08:36 PM
Replies: 1
Views: 607
Posted By 6topham9

HELP! measuring bodies

Hey I could use some help with measuring a body to create holes in the proper spots for the body clips. Whats the best way? There are no pre- sunk starter holes on this body.

Any help is great! I...
04-24-2010, 04:58 PM
Replies: 0
Views: 391
Posted By 6topham9

York Region

So im new to all this, however, is there any place in the Markham area for casual bashing??I saw Markham Stouffville Hospital is under contruction in their south parking lot. Tons of hills and dirt....
04-23-2010, 08:27 PM
Replies: 7
Views: 882
Posted By 6topham9

RE: Savage questions

how much lighter would stocks be?
04-23-2010, 12:26 PM
Replies: 7
Views: 882
Posted By 6topham9

Savage questions

So.. I am new (again) to the hobby. I used to have the "little kid" rc cars, butthatwas 24 years ago. I recentlypurchased a used savage x..... other than that, Idont know the numbers... I assume a...
Showing results 1 to 22 of 22


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service - Do Not Sell My Personal Information -

Copyright 2021 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.