Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Notices
 
Search: Posts Made By: Kris^
Showing results 1 to 25 of 500
Search took 1.23 seconds.
Forum: 3D Flying!
06-12-2004, 05:42 PM
Replies: 88
Views: 8,500
Posted By Kris^

RE: BEST 3D PLANE FOR 2004

yeah Jon. . I asked Andreas to mold me one that was as light as possible, the bare airframe came in about 4 lbs lighter than normal ones do. The BME110 loses another 4 lbs compared to a 150 setup,...
Forum: 3D Flying!
06-12-2004, 04:55 AM
Replies: 88
Views: 8,500
Posted By Kris^

RE: BEST 3D PLANE FOR 2004

yes Tailtwister. . 40% Composite-ARF at 28 lbs .. its written right on the side of the plane. . "40%, 28.5 lbs, 110cc's, Nuff said" That includes the IMAC mandated pilot figure and IP.

As you...
Forum: 3D Flying!
06-11-2004, 09:15 PM
Replies: 88
Views: 8,500
Posted By Kris^

RE: BEST 3D PLANE FOR 2004

I'm sorry. . I've looked at all the responses, but they just aren't quite as good as my 28 lbs 40% Composite-ARF Extra 330 powered by a BME110X on canisters. I have yet to see anything out there...
06-10-2004, 06:31 AM
Replies: 19
Views: 2,672
Posted By Kris^

RE: DA-100 or BME 110 EXTREME

Yes, Klotz. I'm here. :D

When considering an engine there are SO many factors to think about. Weight is certainly one of them, and this is where the BME110 really hits the mark. People will...
Forum: Gas Engines
06-09-2004, 07:52 PM
Replies: 11
Views: 1,370
Posted By Kris^

RE: 3w 106 AI problem...

Some do hook up, some don't Ralph Plain and simple though, the "regulator" actually does control pressure/flow, other wise we would not get mixture deviations when direct air blast hits the front...
Forum: Gas Engines
06-09-2004, 07:00 AM
Replies: 11
Views: 1,370
Posted By Kris^

RE: 3w 106 AI problem...

This really does not sound like a carburetor problem at all, since a mixture problem would maniest itself in a lean out/die symptom or a "supidly rich and blowing raw gas out the exhaust" symptom.
...
Forum: Gas Engines
06-09-2004, 06:13 AM
Replies: 9
Views: 2,866
Posted By Kris^

RE: Biela Propellors

One question Bob. .What the heck are you doing up at 3:20 in the morning??? Geesh :)

As for hauling a lot of props around, it would not be necessary if more people gave reviews of of them and...
Forum: Gas Engines
06-08-2004, 06:44 PM
Replies: 9
Views: 2,866
Posted By Kris^

Biela Propellors

I just wanted to say a few words about the new Biela propellors available from Aircraft International.

I first saw the Biela's last year at Joe Nall, and bought a 27-10 for my 33% Composite-Arf...
Forum: Gas Engines
06-07-2004, 04:35 PM
Replies: 15
Views: 1,379
Posted By Kris^

RE: Broken cranks on gassers

One other thing a lot of people forget is that engines are machines. Any time you have parts moving around, and then stress them and hammer them a bit, there is a possibility of a component failing....
Forum: Gas Engines
06-02-2004, 05:27 AM
Replies: 70
Views: 7,783
Posted By Kris^

RE: DA 100 vs. ZDZ 100 NG

Dick, I always trust YOUR rpm numbers.. seems they closely match the "normal" numbers for a BME102 Evo. Can't argue about whether you own an engine or not if everyone is posting comparable numbers,...
Forum: Gas Engines
06-01-2004, 09:02 PM
Replies: 70
Views: 7,783
Posted By Kris^

RE: DA 100 vs. ZDZ 100 NG

uh. . Excuse me Hugo. .for the "money". . comparable amount spent, the BME110 is far superior over the DA100 in terms of POWER (gain 3-500 rpm) WEIGHT (2 lbs lighter) SIZE (shorter, narrower, rear...
Forum: Gas Engines
05-31-2004, 04:32 PM
Replies: 5
Views: 568
Posted By Kris^

RE: 6 Bolt adapter for BME 110?

I really don't recommend a bolt-on adapter for a 110. The power would make it questionable whether it would hold together. The adapter I had made I have on a 5.8 BME, which has a lot less power. ...
Forum: Gas Engines
05-30-2004, 05:23 AM
Replies: 8
Views: 762
Posted By Kris^

RE: bme 102

I've been using the 100:1 Amsoil synthetic at 80:1 ratio for about 18 months now (ever since I started using it as a matter of fact). Concerns about carbon buildup at this higher level of oil...
Forum: 3D Flying!
05-24-2004, 07:35 PM
Replies: 32
Views: 3,996
Posted By Kris^

RE: 3D Frenzy at Joe Nall

Hey Ben, thanks for the info. I used to fly U-control back in the early 70s' and scratched out a VERY similar looking plane witha K&B .40 on it for Stunt flying. It had the same basic lines, but...
Forum: The Clubhouse
05-24-2004, 04:56 AM
Replies: 79
Views: 6,857
Posted By Kris^

RE: Joe Nall Commentary

The first crash was at about 6:15, on Thursday, over the hangar and lake area. The second one was about 8:00 on Saturday, over the far left side of the runway.
Forum: 3D Flying!
05-23-2004, 07:58 PM
Replies: 32
Views: 3,996
Posted By Kris^

RE: 3D Frenzy at Joe Nall

And NOW. . .some pics of the "Profile Phrenzy" tht's in the works.

A few notes . .there are TWO wing tube locations so that you cna move the wing fore-aft to easier set cg
The receiver sits...
Forum: 3D Flying!
05-23-2004, 07:42 PM
Replies: 32
Views: 3,996
Posted By Kris^

RE: 3D Frenzy at Joe Nall

Just a few "Action Pics" of Ynot with his new toy at Joe Nall.
Forum: The Clubhouse
05-23-2004, 04:19 PM
Replies: 79
Views: 6,857
Posted By Kris^

RE: Joe Nall Commentary

I know the club you were at, Goliath, I'm a member there and know the "National Champ" you are talking about, even a bit aobut the plane and owner. Thing is, the plane was NOT properly pre-flighted...
Forum: The Clubhouse
05-22-2004, 09:08 PM
Replies: 79
Views: 6,857
Posted By Kris^

RE: Joe Nall Commentary

How about. . You break it. .you buy it. I tell everyone who flies any of my planes the same thing . .It's YOUR responsibility if it gets broken, because I'm certainly not going to take the...
05-20-2004, 07:26 PM
Replies: 123
Views: 16,080
Posted By Kris^

RE: Official Joe Nall 2004 Thread - Post your pictures and links to videos here!

Coming from YOU, WC. . I'll take that as a compliment.

A Fuglier version is in the works. . if Ugly flies pretty. . this one should fly like an angel :)

BTW . .Imagine that thing at 14...
Forum: 3D Flying!
05-20-2004, 10:16 AM
Replies: 32
Views: 3,996
Posted By Kris^

RE: 3D Frenzy at Joe Nall

When Ynot flies. . it's ALWAYS a bit strange :)

I am making templates and pieces for the profile fuselage today. . very simple contstruction with internal battery, receiver and semi-internal...
Forum: 3D Flying!
05-19-2004, 10:57 AM
Replies: 32
Views: 3,996
Posted By Kris^

RE: 3D Frenzy at Joe Nall

Right now the 50cc plane is a porky 16 lbs, but I'm confident that with a bit of work it can be brought into the 14-14.5 lbs range for a 2000 square inch wing. This is where the redesign and a bit...
Forum: 3D Flying!
05-19-2004, 05:16 AM
Replies: 32
Views: 3,996
Posted By Kris^

RE: 3D Frenzy at Joe Nall

One thing I forgot to mention. . Ynot told me that the NINE TIME FunFly champion (can never remember his name) came up to Ynot and was telling him how much he LOVED that design. He said he was glad...
Forum: 3D Flying!
05-18-2004, 09:13 PM
Replies: 32
Views: 3,996
Posted By Kris^

RE: 3D Frenzy at Joe Nall

Hey Klotz ! !

Good to finally meet you :)

About the Frenzy . . .the first prototype is kind of a cobbled up work in progress that showed me a lot of what the plane was capable of, but...
Showing results 1 to 25 of 500
 


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service - Do Not Sell My Personal Information -

Copyright 2018 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.