RCU Forums - Search Results

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Notices
Search: Posts Made By: eldoubleu
Showing results 1 to 13 of 13
Search took 0.43 seconds.
Forum: Marketplace
05-20-2018, 04:46 PM
Replies: 7
Views: 1,045
Posted By eldoubleu

Still available?

Still available?
04-30-2014, 10:05 AM
Replies: 37
Views: 17,547
Posted By eldoubleu

Bottom line, that worked, but in my thought...

Bottom line, that worked, but in my thought process if you were to assign AUX2 to Aux1 you would be controlling the servo that is plugged into 6 AUX1 not the one plugged into AUX2

Anywaythank you...
04-30-2014, 08:43 AM
Replies: 37
Views: 17,547
Posted By eldoubleu

I guess I'm still confused on the shuffle thing. ...

I guess I'm still confused on the shuffle thing.

http://www.rcuniverse.com/forum/attachment.php?attachmentid=1991341
Default assignments for 2 Ail 1 Flap
...
04-30-2014, 07:30 AM
Replies: 37
Views: 17,547
Posted By eldoubleu

Andy, The error I mentioned was when I tried to...

Andy,
The error I mentioned was when I tried to upload to RCU, not the 9.
Thanks again for your help. I will search you out on RCG to try and get my brain to follow the logic.

As I said before I...
04-29-2014, 06:13 PM
Replies: 37
Views: 17,547
Posted By eldoubleu

Andy, I'm a little lost with your instructions. ...

Andy, I'm a little lost with your instructions. If I assign AUX 2 to spoilers in the channel input config screen, there is no spoiler selection in the Rx Port Assign screen.
What I'm having a hard...
04-29-2014, 04:43 PM
Replies: 37
Views: 17,547
Posted By eldoubleu

First off, thanks for the reply Andy. I did...

First off, thanks for the reply Andy.
I did realized the change to MOT, I just thought the Rx Ports were assignable, I just don't get the logic of why it reassigned the ports and took away the...
04-29-2014, 01:59 PM
Replies: 37
Views: 17,547
Posted By eldoubleu

Can anyone tell me why, when selecting (Sailplane...

Can anyone tell me why, when selecting (Sailplane Type) 2 Ail 1 Flap, I loose the ability to select Aux 2 under Rx Port Assignments.
I have air brakes/spoilers on Throttle and Aux 2 and would like...
Replies: 24
Views: 19,675
Posted By eldoubleu

RE: Futaba 9C w/Spektrum wiring modification

Question? Does anyone know if the bracket on the antenna end of the coax connection can be removed to lesson the bulk when you tape up the connection? I think this bracket is for protection purposes...
07-30-2010, 09:49 PM
Replies: 664
Views: 120,085
Posted By eldoubleu

RE: Angel S EVO Build Thread

Rich

My screws are about 1/4 inch in from back edge of cowl. But what really matters is that you have the proper overlap of the canopy. My cowl overlaps the canopy 1/2". A lot depends on the...
05-21-2010, 02:51 PM
Replies: 664
Views: 120,085
Posted By eldoubleu

RE: Angel S EVO Build Thread

Finished my Angel S last night and flew the maiden flight today, and all i can say is WOW!...... WOW!....... WOW! and for good measure WOW!!!! I LOVE this plane! I just started sequence/pattern...
05-18-2010, 12:13 PM
Replies: 664
Views: 120,085
Posted By eldoubleu

RE: Angel S EVO Build Thread

Thanks Teo, that was my guess too. It was just odd to me that they were that much longer.

Larry
05-18-2010, 10:49 AM
Replies: 664
Views: 120,085
Posted By eldoubleu

RE: Angel S EVO Build Thread

Hi all,
Finally getting around to assembling my AngelS that I received last November (went to Florida for the winter). I searched this thread and found no mention of a question i have. The tab on...
12-09-2009, 02:52 PM
Replies: 664
Views: 120,085
Posted By eldoubleu

RE: Angel S EVO Build Thread

Hi all, new to this thread, but have read from the beginning.
First I would like to thank all for their opinions and experiences, which have been most helpful. I just received my Angel S and...
Showing results 1 to 13 of 13


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service - Do Not Sell My Personal Information -

Copyright 2021 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.