RCU Forums - Search Results

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Notices
Search: Posts Made By: aspeed
Showing results 1 to 11 of 11
Search took 0.01 seconds.
Forum: Glow Engines
12-02-2018, 05:09 PM
Replies: 135
Views: 7,899
Posted By aspeed

This one is ABC and my X .15 rear rotor rear...

This one is ABC and my X .15 rear rotor rear exhaust is ABC as well. All my other older cross scavenged G .15s and a .19 are lapped steel.
Forum: Glow Engines
12-02-2018, 01:13 PM
Replies: 135
Views: 7,899
Posted By aspeed

The boss has some smoked pork loin on the stove...

The boss has some smoked pork loin on the stove as I speak. She got a new smoker in April, but still uses the old ones. Supertiger X .21 I converted from a...
Forum: Glow Engines
11-20-2018, 06:39 AM
Replies: 135
Views: 7,899
Posted By aspeed

OK, just took a peek at my SF through the fin. It...

OK, just took a peek at my SF through the fin. It seems to be real ABC. There is a brass colour showing through, so maybe that is why they last beter than the FX and later AX. Nickel is a cheaper...
Forum: Glow Engines
11-20-2018, 06:16 AM
Replies: 135
Views: 7,899
Posted By aspeed

Wow lots of action here since I went to sleep. ...

Wow lots of action here since I went to sleep. For the pylon racers with a .46, I checked a few of my 40 -.46 motors unmuffled, and they were all pretty similar with the, ahem, Evolution coming out...
Forum: Glow Engines
11-19-2018, 04:30 PM
Replies: 135
Views: 7,899
Posted By aspeed

I don't think there are any perfect engines. I...

I don't think there are any perfect engines. I would not hesitate using a pipe on any motor, even an OS. I get all of mine for about $20 and don't care. I would not mill the top of the exhaust port...
Forum: Glow Engines
11-19-2018, 01:47 PM
Replies: 135
Views: 7,899
Posted By aspeed

Some motors don't have the slot but drill a small...

Some motors don't have the slot but drill a small hole from behind the front bearing to the intake hole just under the carb. It doesn't hold any oil in the crank/shaft area for lube. There is...
Forum: Glow Engines
11-17-2018, 02:13 PM
Replies: 135
Views: 7,899
Posted By aspeed

The galley doesn't hold oil to seal it. It...

The galley doesn't hold oil to seal it. It allows the negative pressure from the intake to suck the oil back into the crankcase so it doesn't run out the front bearing.
Forum: Glow Engines
11-16-2018, 02:34 PM
Replies: 135
Views: 7,899
Posted By aspeed

Once again, I have not tried it, but would guess...

Once again, I have not tried it, but would guess if tuned, it would always be an improvement over any muffler. A Jett muffler or even a Mousse ca muffler would help. A real pipe needs to be very...
Forum: Glow Engines
11-16-2018, 10:04 AM
Replies: 135
Views: 7,899
Posted By aspeed

I have not run my .46 FX enough to make a...

I have not run my .46 FX enough to make a judgement, but have picked up quite a few OSs over the years from swap meets just when they are priced well. Normally they are pretty good. I have a few...
Forum: Glow Engines
11-16-2018, 08:45 AM
Replies: 135
Views: 7,899
Posted By aspeed

I had an old Supertiger .40 with a worn bearing....

I had an old Supertiger .40 with a worn bearing. The case had a noticeable amount of slop. Still ran fine with no leaks after a new bearing. Really I have not needed to replace that many bearings...
Forum: Glow Engines
11-16-2018, 07:47 AM
Replies: 135
Views: 7,899
Posted By aspeed

A bit of weeping at the front bearing is a...

A bit of weeping at the front bearing is a preferred thing. It means there is lube going to it. Too much can be solved by having a groove between the front bearing and the hole that goes to the...
Showing results 1 to 11 of 11


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service - Do Not Sell My Personal Information -

Copyright 2021 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.